12 open source boards using the SN75176BDR
Real designs built with the SN75176BDR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Motor42
zhbi98
42 × 42 mm82 parts4LMIT8RS485USB
jirihusak
68 × 87 mm120 parts2LGPL-3.04ESP32
Partial Drawer Controller v1
Robast-GmbH
408.7 × 50 mm556 parts4LMIT1RISC-V
LAM-MEW-G3
b4ck5p4c3
53 × 80 mm55 parts2LCERN-OHL-S-2.00AVR/Arduino
ESP8266ControllerCircuit
remyar
53.3 × 68.6 mm29 parts2LNo license0PIC
RoomIO 001
jirihusak
58.2 × 63.9 mm80 parts2LGPL-3.04ESP32
Partial Drawer Controller v1 hotfix
Robast-GmbH
408.7 × 50 mm556 parts4LMIT1RISC-V
LAM-4I4O-REVC
b4ck5p4c3
65 × 80 mm52 parts2LCERN-OHL-S-2.00PIC
RoomSensor 001 MCU
jirihusak
58.2 × 63.9 mm76 parts2LGPL-3.04ESP32
Drawer Controller v4
Robast-GmbH
118 × 47 mm126 parts4LMIT1RISC-V
Lamium
b4ck5p4c3
83 × 62 mm45 parts2LCERN-OHL-S-2.00ESP32
Drawer Controller v4 hotfix
Robast-GmbH
118 × 47 mm126 parts4LMIT1
How designs wire the SN75176BDR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the SN75176BDR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
- The A pin has a series resistor on 2 of 5 designs, most often 10 Ω (then 100 Ω).
- The B pin has a series resistor on 2 of 5 designs, most often 10 Ω (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 5 | Connected to: GND 100% | — |
| Apin 6 | Connected to: A connector 60% |
|
| Bpin 7 | Connected to: A connector 60% |
|
| VCCpin 8 | Connected to: 5V 80% · a signal 20% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Motor42 by zhbi98, RoomIO 001 by jirihusak, Drawer Controller v4 by Robast-GmbH and Lamium by b4ck5p4c3.
The SN75176BDR in open source designs
The gallery holds 12 open source boards using the SN75176BDR from 5 GitHub repositories; a typical one measures about 66.5 × 63 mm and carries around 81 components.
58% are two-layer designs, the rest use four layers or more, and 92% carry an open source license.
The most starred is Motor42 by zhbi98.
Microcontrollers on boards using the SN75176BDR
What boards using the SN75176BDR are built for
SN75176BDR: common questions
Where can I find a SN75176BDR reference design?
Each of the 12 boards on this page is a real design using the SN75176BDR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SN75176BDR VCC pin?
The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the SN75176BDR.
What resistor goes on the SN75176BDR A pin?
The A pin has a series resistor on 2 of 5 designs, most often 10 Ω (then 100 Ω). Counted from the KiCad layouts of 5 open source designs using the SN75176BDR.
What resistor goes on the SN75176BDR B pin?
The B pin has a series resistor on 2 of 5 designs, most often 10 Ω (then 100 Ω). Counted from the KiCad layouts of 5 open source designs using the SN75176BDR.
Which microcontrollers do boards using the SN75176BDR use?
Most are built on ESP32 (4), RISC-V (3), PIC (2) and AVR/Arduino (1).
How big is a typical board using the SN75176BDR?
The median is 66.5 × 63 mm, and 58% are two-layer designs.
What is the most popular open source board using the SN75176BDR?
By GitHub stars, Motor42 by zhbi98, with 8 stars.
Can I simulate one of these boards using the SN75176BDR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.