5 open source boards using the TCAN337
Real designs built with the TCAN337, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
ANUFS-Telemetry
chithigun23
80 × 80 mm157 parts4LNo license0STM32
PS-HVCarrier
lhr-solar
80.5 × 84.7 mm152 parts2LNo license0STM32
ANUFS-APPPD
chithigun23
58.9 × 48.4 mm99 parts4LNo license0STM32
OBD12
samnadol
41.8 × 39.9 mm70 parts4LNo license0STM32
ANUFS-GearPositionSTM
chithigun23
108.8 × 50.9 mm54 parts4LNo license0
How designs wire the TCAN337
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TCAN337 connects to, and the resistors, capacitors and other passives placed on it.
- The FAULT_5 pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ.
- The VCC_3 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
- The TXD_1 pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ.
- The S_8 pin has a resistor to GND on 3 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| TXD_1pin 1 | Connected to: The microcontroller 100% |
|
| GND_2pin 2 | Connected to: GND 100% | — |
| VCC_3pin 3 | Connected to: 3.3V 100% |
|
| FAULT_5pin 5 | Connected to: The microcontroller 80% |
|
| CANH_7pin 7 | Connected to: A connector 100% |
|
| S_8pin 8 | Connected to: The microcontroller 60% · not connected 20% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ANUFS-APPPD by chithigun23, ANUFS-GearPositionSTM by chithigun23, ANUFS-Telemetry by chithigun23 and PS-HVCarrierPCB by lhr-solar.
The TCAN337 in open source designs
The gallery holds 5 open source boards using the TCAN337 from 5 GitHub repositories; a typical one measures about 80 × 50.9 mm and carries around 99 components.
80% use four copper layers or more, and 0% carry an open source license.
The most starred is ANUFS-Telemetry by chithigun23.
Parts used alongside the TCAN337
Microcontrollers on boards using the TCAN337
What boards using the TCAN337 are built for
TCAN337: common questions
Where can I find a TCAN337 reference design?
Each of the 5 boards on this page is a real design using the TCAN337. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the TCAN337 FAULT_5 pin?
The FAULT_5 pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the TCAN337.
What decoupling capacitors do designs use on the TCAN337 VCC_3 pin?
The VCC_3 pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the TCAN337.
What pull-up resistor is used on the TCAN337 TXD_1 pin?
The TXD_1 pin has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the TCAN337.
What parts are used alongside the TCAN337?
The USBLC6-2SC6, AP2112K-3.3, LMR33610ADDAR and STM32F072CBTx appear in the most repositories here.
Which microcontrollers do boards using the TCAN337 use?
Most are built on STM32 (5).
How big is a typical board using the TCAN337?
The median is 80 × 50.9 mm, and 20% are two-layer designs.
What is the most popular open source board using the TCAN337?
By GitHub stars, ANUFS-Telemetry by chithigun23, with 0 stars.
Can I simulate one of these boards using the TCAN337 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.