5 open source boards using the TCMT1100
Real designs built with the TCMT1100, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
Firefish
pimbongaerts
72.2 × 42.8 mm95 parts2LCustom license13CTA control board
PySpice-org
252 × 152 mm614 parts4LNo license9AVR/Arduino
BREAD Slice
FHafting
70 × 100 mm43 parts2LNo license5AVR/Arduino
Slice RLAY
feastorg
70 × 100 mm39 parts2LGPL-3.00AVR/Arduino
Slice RLHT
feastorg
70 × 100 mm36 parts2LGPL-3.00
How designs wire the TCMT1100
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TCMT1100 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 4 of 5 designs, most often 180 Ω (then 300 Ω).
- Pin 2 is tied to GND on 4 of 5 designs.
- Pin 3 is tied to GND on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: GND 80% · a signal 20% | — |
| Pin 3 | Connected to: GND 80% · a signal 20% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Firefish by pimbongaerts, CTA control board by PySpice-org, BREAD Slice by FHafting and Slice RLAY by feastorg.
The TCMT1100 in open source designs
The gallery holds 5 open source boards using the TCMT1100 from 5 GitHub repositories; a typical one measures about 70 × 100 mm and carries around 43 components.
80% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.
The most starred is Firefish by pimbongaerts.
Parts used alongside the TCMT1100
Microcontrollers on boards using the TCMT1100
What boards using the TCMT1100 are built for
TCMT1100: common questions
Where can I find a TCMT1100 reference design?
Each of the 5 boards on this page is a real design using the TCMT1100. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TCMT1100 pin 1?
Pin 1 has a series resistor on 4 of 5 designs, most often 180 Ω (then 300 Ω). Counted from the KiCad layouts of 5 open source designs using the TCMT1100.
How is the TCMT1100 pin 2 connected?
Pin 2 is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TCMT1100.
How is the TCMT1100 pin 3 connected?
Pin 3 is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TCMT1100.
Which microcontrollers do boards using the TCMT1100 use?
Most are built on AVR/Arduino (3) and Microchip SAM (1).
How big is a typical board using the TCMT1100?
The median is 70 × 100 mm, and 80% are two-layer designs.
What is the most popular open source board using the TCMT1100?
By GitHub stars, Firefish by pimbongaerts, with 13 stars.
Can I simulate one of these boards using the TCMT1100 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.