7 open source boards using the TLC5940PWP
Real designs built with the TLC5940PWP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Stm32pe midi
udu3324
307 × 46.1 mm135 parts4LGPL-3.035ESP32
Broadcast clock
espena
239.5 × 239.5 mm440 parts4LGPL-3.028One synapse electronic
RepRapLtd
93 × 73.5 mm137 parts2LGPL-3.08Helpers-Keyboard
siliwho
90.2 × 90.2 mm61 parts2LNo license0STM32
EV19-Dashboard
ASURacingTeam
111.6 × 67.3 mm41 parts2LNo license0EVolver pwm
FYNCH-BIO
33 × 66 mm66 parts4LNo license12AVR/Arduino
RNG Back
QuinnFreedman
50 × 100 mm34 parts2LNo license114
How designs wire the TLC5940PWP
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TLC5940PWP connects to, and the resistors, capacitors and other passives placed on it.
- The IREF pin has a resistor to GND on 7 of 7 designs, most often 2.2 kΩ (then 15 kΩ).
- The VCC pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| IREFpin 27 | Connected to: Signal 100% |
|
| VCCpin 28 | Connected to: 3.3V 100% |
|
| PADpin 29 | Connected to: GND 67% · not connected 33% | — |
25 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RNG Back by QuinnFreedman, Stm32pe midi by udu3324, Broadcast clock by espena and EVolver pwm by FYNCH-BIO.
The TLC5940PWP in open source designs
The gallery holds 7 open source boards using the TLC5940PWP from 7 GitHub repositories; a typical one measures about 93 × 73.5 mm and carries around 66 components.
57% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.
The most starred is RNG Back by QuinnFreedman.
Parts used alongside the TLC5940PWP
Microcontrollers on boards using the TLC5940PWP
What boards using the TLC5940PWP are built for
TLC5940PWP: common questions
Where can I find a TLC5940PWP reference design?
Each of the 7 boards on this page is a real design using the TLC5940PWP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TLC5940PWP IREF pin?
The IREF pin has a resistor to GND on 7 of 7 designs, most often 2.2 kΩ (then 15 kΩ). Counted from the KiCad layouts of 7 open source designs using the TLC5940PWP.
What decoupling capacitors do designs use on the TLC5940PWP VCC pin?
The VCC pin has a decoupling capacitor on 5 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the TLC5940PWP.
Which microcontrollers do boards using the TLC5940PWP use?
Most are built on STM32 (2), AVR/Arduino (1) and ESP32 (1).
How big is a typical board using the TLC5940PWP?
The median is 93 × 73.5 mm, and 57% are two-layer designs.
What is the most popular open source board using the TLC5940PWP?
By GitHub stars, RNG Back by QuinnFreedman, with 114 stars.
Can I simulate one of these boards using the TLC5940PWP before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.