8 open source boards using the TMC2130
Real designs built with the TMC2130, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ESP32 Plotter Controller revB1
MarkJB
99.1 × 55.4 mm57 parts2LMIT9STM32
Buddy
sl1pkn07
105 × 70 mm350 parts6LNo license0TMC2130-smoothie
Duckle29
38.1 × 156.2 mm74 parts2LNo license0Silent stepper v2-bricklet
Tinkerforge
40 × 40 mm68 parts2LNo license0NXP
CarteMere proto
AssociationRobotTelecomStrasbourg
85 × 96 mm46 parts2LNo license0ESP32
ESP32 Plotter Controller revB1 unrouted
MarkJB
99.1 × 55.4 mm49 parts2LMIT9NXP
CarteMere v2.0
AssociationRobotTelecomStrasbourg
92.1 × 72.4 mm44 parts2LNo license0ESP32 Plotter Controller
MarkJB
99.1 × 55.4 mm34 parts2LMIT9
How designs wire the TMC2130
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TMC2130 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 is tied to GND on 3 of 5 designs (a signal on 2).
- Pin 8 has a capacitor to GND on 2 of 4 designs, most often 100 µF (then 100 nF).
- Pin 10 has a decoupling capacitor on 2 of 4 designs, most often 100 nF.
- Pin 33 has a capacitor to GND on 2 of 2 designs, most often 4.7 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: GND 60% · a signal 40% | — |
| Pin 8 | Connected to: Signal 75% · 24V 25% |
|
| Pin 10 | Connected to: 3.3V 50% · a signal 50% |
|
| Pin 17 | Connected to: Not connected 67% · a signal 33% | — |
| Pin 19 | Connected to: Not connected 67% · a signal 33% | — |
| Pin 24 | Connected to: GND 100% | — |
| Pin 33 | Connected to: Signal 100% |
|
| Pin 34 | Connected to: 5V 50% · a signal 50% |
|
25 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ESP32 Plotter Controller by MarkJB, CarteMere proto by AssociationRobotTelecomStrasbourg, TMC2130-smoothie by Duckle29 and Buddy by sl1pkn07.
The TMC2130 in open source designs
The gallery holds 8 open source boards using the TMC2130 from 5 GitHub repositories; a typical one measures about 95.6 × 62.7 mm and carries around 53 components.
88% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is ESP32 Plotter Controller revB1 by MarkJB.
Parts used alongside the TMC2130
What boards using the TMC2130 are built for
TMC2130: common questions
Where can I find a TMC2130 reference design?
Each of the 8 boards on this page is a real design using the TMC2130. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TMC2130 pin 1 connected?
Pin 1 is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the TMC2130.
How is the TMC2130 pin 8 connected?
Pin 8 has a capacitor to GND on 2 of 4 designs, most often 100 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the TMC2130.
What decoupling capacitors do designs use on the TMC2130 pin 10?
Pin 10 has a decoupling capacitor on 2 of 4 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the TMC2130.
Which microcontrollers do boards using the TMC2130 use?
Most are built on ESP32 (2), NXP (2) and STM32 (1).
How big is a typical board using the TMC2130?
The median is 95.6 × 62.7 mm, and 88% are two-layer designs.
What is the most popular open source board using the TMC2130?
By GitHub stars, ESP32 Plotter Controller revB1 by MarkJB, with 9 stars.
Can I simulate one of these boards using the TMC2130 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.