9 open source boards using the TPS563200DDCR
Real designs built with the TPS563200DDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Mainboard
daveshah1
150 × 90 mm709 parts8LMIT40RP2040/RP2350
Access control rp2zk
noahcroit
95.8 × 79 mm82 parts4LNo license0AVR/Arduino
NuBiHo atmega328P
clover-clever
80 × 100 mm77 parts4LNo license0AVR/Arduino
Notemplate
au-ts
27.6 × 13.8 mm64 parts2LNo license0Sata-Multiplier power supply
mattibmt98
64.2 × 53.3 mm56 parts2LNo license0Power wheel ubuck
ALeggeUp
26 × 23.5 mm15 parts2LCC-BY-SA-4.00- schematic only · 1 parts
GWARIMPA-SITE
Olatmatics
1 parts4LNo license0 STM32
SRAD Altimeter
waterloo-rocketry
71.4 × 71.4 mm133 parts4LGPL-3.015LionsOS Robot Power Board
au-ts
100 × 100 mm55 parts4LNo license0
How designs wire the TPS563200DDCR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS563200DDCR connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a series capacitor on 7 of 7 designs, most often 100 nF.
- The SW pin has a inductor on 7 of 7 designs, most often 1.5 µH (then 3.3 µH).
- The VFB pin has a resistor to GND on 7 of 7 designs, most often 10 kΩ.
- The VBST pin has a series capacitor on 7 of 7 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| SWpin 2 | Connected to: Signal 100% |
|
| VINpin 3 | Connected to: 12V 86% |
|
| VFBpin 4 | Connected to: Signal 100% |
|
| VBSTpin 6 | Connected to: Signal 100% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mainboard by daveshah1, SRAD Altimeter by waterloo-rocketry, Power wheel ubuck by ALeggeUp and Notemplate pcb by au-ts.
The TPS563200DDCR in open source designs
The gallery holds 9 open source boards using the TPS563200DDCR from 8 GitHub repositories; a typical one measures about 75.7 × 75.2 mm and carries around 64 components.
67% use four copper layers or more, and 33% carry an open source license.
The most starred is Mainboard by daveshah1.
Microcontrollers on boards using the TPS563200DDCR
What boards using the TPS563200DDCR are built for
TPS563200DDCR: common questions
Where can I find a TPS563200DDCR reference design?
Each of the 9 boards on this page is a real design using the TPS563200DDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS563200DDCR SW pin connected?
The SW pin has a series capacitor on 7 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the TPS563200DDCR.
What resistor goes on the TPS563200DDCR VFB pin?
The VFB pin has a resistor to GND on 7 of 7 designs, most often 10 kΩ. Counted from the KiCad layouts of 7 open source designs using the TPS563200DDCR.
How is the TPS563200DDCR VBST pin connected?
The VBST pin has a series capacitor on 7 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the TPS563200DDCR.
Which microcontrollers do boards using the TPS563200DDCR use?
Most are built on AVR/Arduino (2), FPGA (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the TPS563200DDCR?
The median is 75.7 × 75.2 mm, and 33% are two-layer designs.
What is the most popular open source board using the TPS563200DDCR?
By GitHub stars, Mainboard by daveshah1, with 40 stars.
Can I simulate one of these boards using the TPS563200DDCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.