19 open source boards using the TPS62160DGKR

Real designs built with the TPS62160DGKR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

19 boardsClear filters|Most starred

How designs wire the TPS62160DGKR

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the TPS62160DGKR connects to, and the resistors, capacitors and other passives placed on it.

  • The SW_7 pin has a inductor on 6 of 6 designs, most often 2.2 µH (then 3.3 µH).
  • The EN_3 pin is tied to 5V on 6 of 7 designs.
  • The FB_5 pin has a pull-up to 5V on 5 of 7 designs, most often 220 kΩ (then 316 kΩ).
  • The FB_5 pin has a resistor to GND on 5 of 7 designs, most often 47 kΩ (then 100 kΩ).
PGND_1pin 1Connected to: GND 71%
VIN_2pin 2Connected to: 12V 71%
  • Decoupling capacitor on 43% · 10 µF (3)
EN_3pin 3Connected to: 5V 86%
AGND_4pin 4Connected to: GND 71%
FB_5pin 5Connected to: Signal 86%
  • Pull-up to 5V on 71% · 220 kΩ (1), 316 kΩ (1), 340 Ω (1)
  • Resistor to GND on 71% · 47 kΩ (1), 100 kΩ (1), 820 Ω (1)
VOS_6pin 6Connected to: 5V 83% · a signal 17%
  • Inductor on 83% · 2.2 µH (4), 3.3 µH (1)
SW_7pin 7Connected to: Signal 100%
  • Inductor on 100% · 2.2 µH (5), 3.3 µH (1)
PG_8pin 8Connected to: Signal 67% · not connected 33%
  • Pull-up to 5V on 50% · 100 kΩ (3)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Tail lights by chrskly, Lightclock by Anvarys, My first linux board by clarkmcc and Quad Preamp and 4-Channel Ambisonic Recorder by jdg511.

The TPS62160DGKR in open source designs

The gallery holds 19 open source boards using the TPS62160DGKR from 7 GitHub repositories; a typical one measures about 138 × 114 mm and carries around 191 components.

74% use four copper layers or more, and 5% carry an open source license.

The most starred is Tail lights by chrskly.

Microcontrollers on boards using the TPS62160DGKR

What boards using the TPS62160DGKR are built for

TPS62160DGKR: common questions

Where can I find a TPS62160DGKR reference design?

Each of the 19 boards on this page is a real design using the TPS62160DGKR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS62160DGKR SW_7 pin connected?

The SW_7 pin has a inductor on 6 of 6 designs, most often 2.2 µH (then 3.3 µH). Counted from the KiCad layouts of 7 open source designs using the TPS62160DGKR.

How is the TPS62160DGKR EN_3 pin connected?

The EN_3 pin is tied to 5V on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the TPS62160DGKR.

What pull-up resistor is used on the TPS62160DGKR FB_5 pin?

The FB_5 pin has a pull-up to 5V on 5 of 7 designs, most often 220 kΩ (then 316 kΩ). Counted from the KiCad layouts of 7 open source designs using the TPS62160DGKR.

Which microcontrollers do boards using the TPS62160DGKR use?

Most are built on NXP (12), ESP32 (3), AVR/Arduino (1) and RP2040/RP2350 (1).

How big is a typical board using the TPS62160DGKR?

The median is 138 × 114 mm, and 26% are two-layer designs.

What is the most popular open source board using the TPS62160DGKR?

By GitHub stars, Tail lights by chrskly, with 2 stars.

Can I simulate one of these boards using the TPS62160DGKR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part