5 open source boards using the TPS7A4001DGNR
Real designs built with the TPS7A4001DGNR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Pandore
filliformes
260 × 110 mm759 parts4LNo license2EBM7-2608-V23-MOSFET
2solve
60 × 60 mm155 parts4LNo license0EBM7-2608-V3
2solve
60 × 60 mm135 parts4LNo license0EMB2-2609-V5
2solve
60 × 60 mm123 parts4LNo license0AVR/Arduino
5S-Blower-Controller
10htts
77 × 62 mm48 parts2LCERN-OHL-S-2.00
How designs wire the TPS7A4001DGNR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPS7A4001DGNR connects to, and the resistors, capacitors and other passives placed on it.
- The FB_2 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ (then 13 kΩ).
- The NC_3 pin is left unconnected on 4 of 5 designs.
- The EN_5 pin is tied to 24V on 4 of 5 designs.
- The NC_6 pin is left unconnected on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUT_1pin 1 | Connected to: 12V 60% · a signal 40% | — |
| FB_2pin 2 | Connected to: Signal 100% |
|
| NC_3pin 3 | Connected to: Not connected 80% · a signal 20% | — |
| GND_4pin 4 | Connected to: GND 80% · a signal 20% | — |
| EN_5pin 5 | Connected to: 24V 80% · a signal 20% | — |
| NC_6pin 6 | Connected to: Not connected 80% · a signal 20% | — |
| NC_7pin 7 | Connected to: Not connected 80% · a signal 20% | — |
| IN_8pin 8 | Connected to: 24V 80% · a signal 20% | — |
| PAD_9pin 9 | Connected to: GND 80% · a signal 20% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pandore by filliformes, 5S-Blower-Controller by 10htts, EBM7-2608-V23-MOSFET by 2solve and EBM7-2608-V3 by 2solve.
The TPS7A4001DGNR in open source designs
The gallery holds 5 open source boards using the TPS7A4001DGNR from 5 GitHub repositories; a typical one measures about 60 × 60 mm and carries around 135 components.
80% use four copper layers or more, and 20% carry an open source license.
The most starred is Pandore by filliformes.
Parts used alongside the TPS7A4001DGNR
Microcontrollers on boards using the TPS7A4001DGNR
What boards using the TPS7A4001DGNR are built for
TPS7A4001DGNR: common questions
Where can I find a TPS7A4001DGNR reference design?
Each of the 5 boards on this page is a real design using the TPS7A4001DGNR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS7A4001DGNR FB_2 pin?
The FB_2 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ (then 13 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPS7A4001DGNR.
How is the TPS7A4001DGNR NC_3 pin connected?
The NC_3 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TPS7A4001DGNR.
How is the TPS7A4001DGNR EN_5 pin connected?
The EN_5 pin is tied to 24V on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TPS7A4001DGNR.
What parts are used alongside the TPS7A4001DGNR?
The ISO7141CCDBQR, TL431BQDBZR, TPS26613DDFR, AD7124-8BCPZ and ADR4525BRZ appear in the most repositories here.
Which microcontrollers do boards using the TPS7A4001DGNR use?
Most are built on AVR/Arduino (1) and RP2040/RP2350 (1).
How big is a typical board using the TPS7A4001DGNR?
The median is 60 × 60 mm, and 20% are two-layer designs.
What is the most popular open source board using the TPS7A4001DGNR?
By GitHub stars, Pandore by filliformes, with 2 stars.
Can I simulate one of these boards using the TPS7A4001DGNR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.