6 open source boards using the TXB0108RGYR
Real designs built with the TXB0108RGYR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Fast open switch r1.0
PCB-Arts
230 × 225 mm909 parts12LNo license14STM32
Sabre-Integrated flight controller
CircuitGuy943
60 × 137.1 mm260 parts4LGPL-3.02ESP32
Fibel2
nikolozka
210 × 148 mm434 parts4LNo license0ESP32
AWS PROJECT
marydovika
206.3 × 91.3 mm207 parts2LNo license0PIC
SensorHub
komoro13
130 parts2LNo license0ESP32
EdgeLink S3 Cellular
CDonohoe-Designs
56 × 52 mm93 parts4LNo license0
How designs wire the TXB0108RGYR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TXB0108RGYR connects to, and the resistors, capacitors and other passives placed on it.
- The VCCA pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
- The VCCB pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF.
- The A8 pin is left unconnected on 4 of 5 designs.
- The OE pin is tied to 3.3V on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCApin 2 | Connected to: 1.8V 100% |
|
| A8pin 9 | Connected to: Not connected 80% · a signal 20% | — |
| OEpin 10 | Connected to: 3.3V 80% · a signal 20% | — |
| GNDpin 11 | Connected to: GND 100% | — |
| B8pin 12 | Connected to: Not connected 80% · a signal 20% | — |
| B3pin 17 | Connected to: A connector 40% · not connected 20% |
|
| B2pin 18 | Connected to: A connector 40%, the microcontroller 40% |
|
| VCCBpin 19 | Connected to: 3.3V 80% · a signal 20% |
|
| EPpin 21 | Connected to: GND 100% | — |
12 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Fast open switch r1.0 by PCB-Arts, Sabre-Integrated flight controller by CircuitGuy943, EdgeLink S3 Cellular by CDonohoe-Designs and AWS PROJECT by marydovika.
The TXB0108RGYR in open source designs
The gallery holds 6 open source boards using the TXB0108RGYR from 6 GitHub repositories; a typical one measures about 206.3 × 137.1 mm and carries around 234 components.
67% use four copper layers or more, and 17% carry an open source license.
The most starred is Fast open switch r1.0 by PCB-Arts.
What boards using the TXB0108RGYR are built for
TXB0108RGYR: common questions
Where can I find a TXB0108RGYR reference design?
Each of the 6 boards on this page is a real design using the TXB0108RGYR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TXB0108RGYR VCCA pin?
The VCCA pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the TXB0108RGYR.
What decoupling capacitors do designs use on the TXB0108RGYR VCCB pin?
The VCCB pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the TXB0108RGYR.
How is the TXB0108RGYR A8 pin connected?
The A8 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TXB0108RGYR.
Which microcontrollers do boards using the TXB0108RGYR use?
Most are built on ESP32 (3), FPGA (1), PIC (1) and STM32 (1).
How big is a typical board using the TXB0108RGYR?
The median is 206.3 × 137.1 mm, and 33% are two-layer designs.
What is the most popular open source board using the TXB0108RGYR?
By GitHub stars, Fast open switch r1.0 by PCB-Arts, with 14 stars.
Can I simulate one of these boards using the TXB0108RGYR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.