9 open source boards using the VTL5C

Real designs built with the VTL5C, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the VTL5C

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the VTL5C connects to, and the resistors, capacitors and other passives placed on it.

  • The - pin has a resistor to GND on 5 of 6 designs, most often 330 Ω (then 1 kΩ).
  • The + pin has a series resistor on 5 of 6 designs, most often 100 kΩ (then 10 kΩ).
  • Pin 3 has a series resistor on 4 of 6 designs, most often 330 Ω (then 470 kΩ).
  • Pin 4 has a series resistor on 3 of 6 designs, most often 200 kΩ (then 1 kΩ).
-pin 1Connected to: Signal 100%
  • Resistor to GND on 83% · 330 Ω (2), 1 kΩ (2), 100 kΩ (1)
+pin 2Connected to: Signal 100%
  • Series resistor on 83% · 100 kΩ (2), 10 kΩ (1), 680 Ω (1)
Pin 3Connected to: A connector 33%, VTL5C 33%
  • Series resistor on 67% · 330 Ω (2), 470 kΩ (1), 1 MΩ (1)
  • Series capacitor on 33% · 4.7 nF (2)
Pin 4Connected to: Signal 83% · GND 17%
  • Series resistor on 50% · 200 kΩ (1), 1 kΩ (1), 15 kΩ (1)
  • Series capacitor on 33% · 1 nF (1), 47 nF (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hihat by bread-modular, Corona mainBoard by coriolisinstruments, Multi saturation module by DIYSynthMNL and Synth by adeboni.

The VTL5C in open source designs

The gallery holds 9 open source boards using the VTL5C from 6 GitHub repositories; a typical one measures about 40 × 100 mm and carries around 52 components.

78% are two-layer designs, the rest use four layers or more, and 78% carry an open source license.

The most starred is Hihat by bread-modular.

Parts used alongside the VTL5C

Microcontrollers on boards using the VTL5C

What boards using the VTL5C are built for

VTL5C: common questions

Where can I find a VTL5C reference design?

Each of the 9 boards on this page is a real design using the VTL5C. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the VTL5C - pin?

The - pin has a resistor to GND on 5 of 6 designs, most often 330 Ω (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the VTL5C.

What resistor goes on the VTL5C + pin?

The + pin has a series resistor on 5 of 6 designs, most often 100 kΩ (then 10 kΩ). Counted from the KiCad layouts of 6 open source designs using the VTL5C.

What resistor goes on the VTL5C pin 3?

Pin 3 has a series resistor on 4 of 6 designs, most often 330 Ω (then 470 kΩ). Counted from the KiCad layouts of 6 open source designs using the VTL5C.

Which microcontrollers do boards using the VTL5C use?

Most are built on AVR/Arduino (1).

How big is a typical board using the VTL5C?

The median is 40 × 100 mm, and 78% are two-layer designs.

What is the most popular open source board using the VTL5C?

By GitHub stars, Hihat by bread-modular, with 67 stars.

Can I simulate one of these boards using the VTL5C before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part