7 open source boards using the YAC512
Real designs built with the YAC512, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ES688 ISA8
hkzlab
104.1 × 99.1 mm121 parts4LCC-BY-NC-4.046Rcbus opl3
electrified
100 × 50 mm32 parts2LNo license6Resound-2-MCA-OPL3
texelec
131.1 × 88.3 mm53 parts2LNo license54op drum module rev2
vk2gpu
99.1 × 99.1 mm117 parts2LNo license2Rcbus opl3-site
electrified
100 × 50 mm32 parts2LNo license0Panel
vk2gpu
99.1 × 99.1 mm117 parts2LNo license2Backup1
vk2gpu
102.9 × 92.7 mm101 parts2LNo license2
How designs wire the YAC512
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the YAC512 connects to, and the resistors, capacitors and other passives placed on it.
- The CH1 pin has a capacitor to GND on 5 of 5 designs, most often 2.7 nF.
- The CH2 pin has a capacitor to GND on 5 of 5 designs, most often 2.7 nF.
- The SWIN pin has a series resistor on 5 of 5 designs, most often 33 Ω.
- The AOUT pin has a capacitor to GND on 5 of 5 designs, most often 68 pF (then 33 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1, 3 | Connected to: 5V 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| FSELpin 6 | Connected to: 5V 100% | — |
| TST1pin 9 | Connected to: 5V 100% | — |
| CH1pin 10 | Connected to: TL074CDT 40%, TL074 40% |
|
| CH2pin 11 | Connected to: TL074CDT 40%, TL074 40% |
|
| SWINpin 12 | Connected to: Signal 100% |
|
| AOUTpin 13 | Connected to: TL074CDT 40%, TL074 40% |
|
| TST2pin 15 | Connected to: Not connected 100% | — |
| CVpin 16 | Connected to: TL074CDT 40%, TL074 40% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ES688 ISA8 by hkzlab, Rcbus opl3 by electrified, Resound-2-MCA-OPL3 by texelec and 4op drum module rev2 by vk2gpu.
The YAC512 in open source designs
The gallery holds 7 open source boards using the YAC512 from 5 GitHub repositories; a typical one measures about 100 × 92.7 mm and carries around 101 components.
86% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is ES688 ISA8 by hkzlab.
Parts used alongside the YAC512
What boards using the YAC512 are built for
YAC512: common questions
Where can I find a YAC512 reference design?
Each of the 7 boards on this page is a real design using the YAC512. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the YAC512 CH1 pin connected?
The CH1 pin has a capacitor to GND on 5 of 5 designs, most often 2.7 nF. Counted from the KiCad layouts of 5 open source designs using the YAC512.
How is the YAC512 CH2 pin connected?
The CH2 pin has a capacitor to GND on 5 of 5 designs, most often 2.7 nF. Counted from the KiCad layouts of 5 open source designs using the YAC512.
What resistor goes on the YAC512 SWIN pin?
The SWIN pin has a series resistor on 5 of 5 designs, most often 33 Ω. Counted from the KiCad layouts of 5 open source designs using the YAC512.
What parts are used alongside the YAC512?
The YMF262, CD74HCT688M96, L78L05, TL074 and TL074CDT appear in the most repositories here.
How big is a typical board using the YAC512?
The median is 100 × 92.7 mm, and 86% are two-layer designs.
What is the most popular open source board using the YAC512?
By GitHub stars, ES688 ISA8 by hkzlab, with 46 stars.
Can I simulate one of these boards using the YAC512 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.