7 open source boards using the 74HC595N
Real designs built with the 74HC595N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ChessBoard
Odissus
218 × 218 mm137 parts2LNo license0ESP32
Reflex machine
Mhamednoui
160 × 125 mm123 parts2LNo license0AVR/Arduino
EV-Battery-Level-Indicator-Using-ATtiny85-7-Segment-Display
manoj-karna17
136 × 60 mm15 parts2LNo license0HeaterMeterLCD
CapnBry
69.9 × 41.3 mm21 partsMIT557Control board
m0xpd
108 × 88 mm97 parts2LCC-BY-SA-4.025Braids through hole V1.1 CONTROL
sebastianbeyer
87 × 96 mm45 partsNo license15SERIAL PIC PROGRAMMER
Mhamednoui
160 × 99.1 mm55 parts2LNo license0
How designs wire the 74HC595N
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the 74HC595N connects to, and the resistors, capacitors and other passives placed on it.
- The QH* pin is left unconnected on 5 of 5 designs.
- The SCL pin is tied to 5V on 4 of 5 designs.
- The G pin is tied to GND on 4 of 5 designs.
- The QB pin has a series resistor on 3 of 6 designs, most often 220 Ω (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| QBpin 1 | Connected to: Signal 100% |
|
| QCpin 2 | Connected to: Signal 83% · GND 17% |
|
| QDpin 3 | Connected to: Signal 83% · VCC 17% |
|
| QEpin 4 | Connected to: Signal 100% |
|
| QFpin 5 | Connected to: Signal 100% |
|
| GNDpin 8 | Connected to: GND 100% | — |
| QH*pin 9 | Connected to: Not connected 100% | — |
| SCLpin 10 | Connected to: 5V 80% · a signal 20% | — |
| Gpin 13 | Connected to: GND 80% · VDD 20% | — |
| QApin 15 | Connected to: Signal 100% |
|
| VCCpin 16 | Connected to: 5V 80% · a signal 20% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include HeaterMeterLCD by CapnBry, Control board by m0xpd, Braids through hole V1.1 CONTROL by sebastianbeyer and EV-Battery-Level-Indicator-Using-ATtiny85-7-Segment-Display by manoj-karna17.
The 74HC595N in open source designs
The gallery holds 7 open source boards using the 74HC595N from 6 GitHub repositories; a typical one measures about 136 × 96 mm and carries around 55 components.
100% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is HeaterMeterLCD by CapnBry.
Microcontrollers on boards using the 74HC595N
What boards using the 74HC595N are built for
74HC595N: common questions
Where can I find a 74HC595N reference design?
Each of the 7 boards on this page is a real design using the 74HC595N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 74HC595N QH* pin connected?
The QH* pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 6 open source designs using the 74HC595N.
How is the 74HC595N SCL pin connected?
The SCL pin is tied to 5V on 4 of 5 designs. Counted from the KiCad layouts of 6 open source designs using the 74HC595N.
How is the 74HC595N G pin connected?
The G pin is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 6 open source designs using the 74HC595N.
Which microcontrollers do boards using the 74HC595N use?
Most are built on AVR/Arduino (1) and ESP32 (1).
How big is a typical board using the 74HC595N?
The median is 136 × 96 mm, and 100% are two-layer designs.
What is the most popular open source board using the 74HC595N?
By GitHub stars, HeaterMeterLCD by CapnBry, with 557 stars.
Can I simulate one of these boards using the 74HC595N before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.