5 open source boards using the 93LC46C

Real designs built with the 93LC46C, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the 93LC46C

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the 93LC46C connects to, and the resistors, capacitors and other passives placed on it.

  • The SCLK pin has a series resistor on 5 of 5 designs, most often 10 kΩ.
  • The DI pin has a series resistor on 5 of 5 designs, most often 10 kΩ (then 2.2 kΩ).
  • The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF.
  • The ORG pin is tied to VCC on 4 of 5 designs.
SCLKpin 2Connected to: RTL8019AS 80%, SST39SF040 60%, a connector 60%
  • Series resistor on 100% · 10 kΩ (5)
DIpin 3Connected to: RTL8019AS 80%, SST39SF040 60%, a connector 60%
  • Series resistor on 100% · 10 kΩ (4), 2.2 kΩ (1)
GNDpin 5Connected to: GND 100%
ORGpin 6Connected to: VCC 80% · a signal 20%
NCpin 7Connected to: Not connected 100%
VCCpin 8Connected to: VCC 80% · a signal 20%
  • Decoupling capacitor on 100% · 100 nF (4)

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Isa8 eth by skiselev, Tedium X8 by jboone, Isa8 eth main by theos10 and EC1834-LAN by mgoegel.

The 93LC46C in open source designs

The gallery holds 5 open source boards using the 93LC46C from 5 GitHub repositories; a typical one measures about 104.1 × 74.9 mm and carries around 30 components.

50% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.

The most starred is Isa8 eth by skiselev.

Parts used alongside the 93LC46C

Microcontrollers on boards using the 93LC46C

What boards using the 93LC46C are built for

93LC46C: common questions

Where can I find a 93LC46C reference design?

Each of the 5 boards on this page is a real design using the 93LC46C. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the 93LC46C SCLK pin?

The SCLK pin has a series resistor on 5 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the 93LC46C.

What resistor goes on the 93LC46C DI pin?

The DI pin has a series resistor on 5 of 5 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 5 open source designs using the 93LC46C.

What decoupling capacitors do designs use on the 93LC46C VCC pin?

The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the 93LC46C.

Which microcontrollers do boards using the 93LC46C use?

Most are built on FPGA (1).

How big is a typical board using the 93LC46C?

The median is 104.1 × 74.9 mm, and 50% are two-layer designs.

What is the most popular open source board using the 93LC46C?

By GitHub stars, Isa8 eth by skiselev, with 150 stars.

Can I simulate one of these boards using the 93LC46C before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part