5 open source boards using the ACS758

Real designs built with the ACS758, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the ACS758

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ACS758 connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 pF).
  • The VIOUT pin has a series resistor on 2 of 5 designs, most often 10 kΩ (then 22 kΩ).
  • The IP+ pin has a capacitor to GND on 2 of 5 designs, most often 10 µF (then 220 µF).
VCCpin 1Connected to: 5V 60% · GND 20% · a signal 20%
  • Decoupling capacitor on 80% · 100 nF (8), 10 pF (1)
GNDpin 2Connected to: GND 86%
VIOUTpin 3Connected to: A connector 40%
  • Series resistor on 40% · 10 kΩ (1), 22 kΩ (1)
IP+pin 4Connected to: A connector 60%
  • Capacitor to GND on 40% · 10 µF (1), 220 µF (1), 2.2 nF (1)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ArmPowerBoardV3 by UofSSpaceTeam, AI Inverter Project by HNadeemTahir, Server lader by ep092 and Neo by IstratieStefan.

The ACS758 in open source designs

The gallery holds 5 open source boards using the ACS758 from 5 GitHub repositories; a typical one measures about 119.1 × 98.6 mm and carries around 75 components.

100% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.

The most starred is ArmPowerBoardV3 by UofSSpaceTeam.

Microcontrollers on boards using the ACS758

What boards using the ACS758 are built for

ACS758: common questions

Where can I find a ACS758 reference design?

Each of the 5 boards on this page is a real design using the ACS758. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ACS758 VCC pin?

The VCC pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 pF). Counted from the KiCad layouts of 5 open source designs using the ACS758.

What resistor goes on the ACS758 VIOUT pin?

The VIOUT pin has a series resistor on 2 of 5 designs, most often 10 kΩ (then 22 kΩ). Counted from the KiCad layouts of 5 open source designs using the ACS758.

How is the ACS758 IP+ pin connected?

The IP+ pin has a capacitor to GND on 2 of 5 designs, most often 10 µF (then 220 µF). Counted from the KiCad layouts of 5 open source designs using the ACS758.

Which microcontrollers do boards using the ACS758 use?

Most are built on AVR/Arduino (2), ESP32 (1) and ESP8266 (1).

How big is a typical board using the ACS758?

The median is 119.1 × 98.6 mm, and 100% are two-layer designs.

What is the most popular open source board using the ACS758?

By GitHub stars, ArmPowerBoardV3 by UofSSpaceTeam, with 5 stars.

Can I simulate one of these boards using the ACS758 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part