6 open source boards using the AP22804AW5-7
Real designs built with the AP22804AW5-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Debugotron - USB Switch
alvarop
60 × 60 mm72 parts4LBSD-3-Clause52ESPNut-D1
CIRCUITSTATE
44 × 20 mm64 parts2LMIT2AQEYE-SB-D1
CIRCUITSTATE
80 × 30 mm65 parts2LMIT1STM32
Pcb mantis
si-nalsal
125.2 × 90 mm277 parts6LCERN-OHL-S-2.00Raspberry Pi
EverestCM4
PionixPublic
112.7 × 67.8 mm207 parts4LCERN-OHL-P-2.068IMPISH PS Toggles Board
umn-impish
90 × 90 mm83 parts4LMPL-2.01
How designs wire the AP22804AW5-7
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the AP22804AW5-7 connects to, and the resistors, capacitors and other passives placed on it.
- The IN pin is tied to 5V on 4 of 6 designs (a signal on 2).
- The FLG pin has a pull-up to 3.3V on 3 of 6 designs, most often 10 kΩ.
- The EN pin has a resistor to GND on 3 of 6 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| FLGpin 3 | Connected to: Signal 50% · not connected 33% · GND 17% |
|
| ENpin 4 | Connected to: A connector 50% |
|
| INpin 5 | Connected to: 5V 67% · a signal 33% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EverestCM4 by PionixPublic, Debugotron - USB Switch by alvarop, ESPNut-D1 by CIRCUITSTATE and AQEYE-SB-D1 by CIRCUITSTATE.
The AP22804AW5-7 in open source designs
The gallery holds 6 open source boards using the AP22804AW5-7 from 6 GitHub repositories; a typical one measures about 85 × 63.9 mm and carries around 78 components.
67% use four copper layers or more, and 100% carry an open source license.
The most starred is EverestCM4 by PionixPublic.
Microcontrollers on boards using the AP22804AW5-7
What boards using the AP22804AW5-7 are built for
AP22804AW5-7: common questions
Where can I find a AP22804AW5-7 reference design?
Each of the 6 boards on this page is a real design using the AP22804AW5-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP22804AW5-7 IN pin connected?
The IN pin is tied to 5V on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 6 open source designs using the AP22804AW5-7.
What pull-up resistor is used on the AP22804AW5-7 FLG pin?
The FLG pin has a pull-up to 3.3V on 3 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the AP22804AW5-7.
What resistor goes on the AP22804AW5-7 EN pin?
The EN pin has a resistor to GND on 3 of 6 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 6 open source designs using the AP22804AW5-7.
Which microcontrollers do boards using the AP22804AW5-7 use?
Most are built on Raspberry Pi (1) and STM32 (1).
How big is a typical board using the AP22804AW5-7?
The median is 85 × 63.9 mm, and 33% are two-layer designs.
What is the most popular open source board using the AP22804AW5-7?
By GitHub stars, EverestCM4 by PionixPublic, with 68 stars.
Can I simulate one of these boards using the AP22804AW5-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.