9 open source boards using the ATmega32A-PU
Real designs built with the ATmega32A-PU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0kAVR/Arduino
Mysterium
coseyfannitutti
347.7 × 146.6 mm206 parts2LGPL-3.0543AVR/Arduino
Bonsai
Retne01
348.5 × 165.6 mm191 parts2LNo license24AVR/Arduino
LCK75
lyso1
317.3 × 154.8 mm201 parts2LMIT10AVR/Arduino
Pinstripe
null-ll
323.9 × 123 mm162 parts2LGPL-2.09AVR/Arduino
Skylight
drakumus
126 × 103 mm81 parts2LNo license2AVR/Arduino
Thermocouple 8ch
mahmoud-elghamry
250 × 140 mm201 parts2LNo license0AVR/Arduino
KB79
jonathan512
308 × 153 mm181 parts2LGPL-3.00AVR/Arduino
Thermocouple meter
mahmoud-elghamry
150 × 70 mm30 parts2LNo license0
How designs wire the ATmega32A-PU
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the ATmega32A-PU connects to, and the resistors, capacitors and other passives placed on it.
- The XTAL2_12 pin has a crystal on 8 of 8 designs, most often 16 MHz (then 8 MHz).
- The XTAL1_13 pin has a crystal on 8 of 8 designs, most often 16 MHz (then 8 MHz).
- The XTAL2_12 pin has a capacitor to GND on 7 of 8 designs, most often 22 pF.
- The XTAL1_13 pin has a capacitor to GND on 7 of 8 designs, most often 22 pF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RESET_9pin 9 | Connected to: A connector 100% |
|
| VCC_10pin 10 | Connected to: 5V 88% |
|
| GND_11pin 11 | Connected to: GND 88% | — |
| XTAL2_12pin 12 | Connected to: Signal 100% |
|
| XTAL1_13pin 13 | Connected to: Signal 100% |
|
| PD2_16pin 16 | Connected to: Signal 100% |
|
| PD3_17pin 17 | Connected to: Signal 100% |
|
| AVCC_30pin 30 | Connected to: 5V 88% |
|
| GND_31pin 31 | Connected to: GND 88% | — |
| AREF_32pin 32 | Connected to: Not connected 88% | — |
30 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Discipline by coseyfannitutti, Mysterium pcb by coseyfannitutti, Bonsai by Retne01 and LCK75 by lyso1.
The ATmega32A-PU in open source designs
The gallery holds 9 open source boards using the ATmega32A-PU from 8 GitHub repositories; a typical one measures about 308 × 140 mm and carries around 181 components.
100% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Discipline by coseyfannitutti.
Microcontrollers on boards using the ATmega32A-PU
What boards using the ATmega32A-PU are built for
ATmega32A-PU: common questions
Where can I find a ATmega32A-PU reference design?
Each of the 9 boards on this page is a real design using the ATmega32A-PU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ATmega32A-PU XTAL2_12 pin connected?
The XTAL2_12 pin has a crystal on 8 of 8 designs, most often 16 MHz (then 8 MHz). Counted from the KiCad layouts of 8 open source designs using the ATmega32A-PU.
How is the ATmega32A-PU XTAL1_13 pin connected?
The XTAL1_13 pin has a crystal on 8 of 8 designs, most often 16 MHz (then 8 MHz). Counted from the KiCad layouts of 8 open source designs using the ATmega32A-PU.
What resistor goes on the ATmega32A-PU PD2_16 pin?
The PD2_16 pin has a series resistor on 7 of 8 designs, most often 75 Ω (then 68 Ω). Counted from the KiCad layouts of 8 open source designs using the ATmega32A-PU.
Which microcontrollers do boards using the ATmega32A-PU use?
Most are built on AVR/Arduino (9).
How big is a typical board using the ATmega32A-PU?
The median is 308 × 140 mm, and 100% are two-layer designs.
What is the most popular open source board using the ATmega32A-PU?
By GitHub stars, Discipline by coseyfannitutti, with 1,006 stars.
Can I simulate one of these boards using the ATmega32A-PU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.