7 open source boards using the ATmega88PA-A

Real designs built with the ATmega88PA-A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the ATmega88PA-A

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATmega88PA-A connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pins have a decoupling capacitor on 6 of 6 designs, most often 100 nF.
  • The AVCC pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 4.7 µF).
  • The PC0 pin has a series resistor on 4 of 6 designs, most often 680 Ω (then 30 kΩ).
  • The PC1 pin has a series resistor on 4 of 6 designs, most often 4.7 kΩ (then 30 kΩ).
PD3pin 1Connected to: Signal 67% · not connected 33%
  • Series resistor on 33% · 1 kΩ (4)
PD4pin 2Connected to: Signal 67% · not connected 33%
  • Series resistor on 33% · 1 kΩ (2)
GNDpin 3, 5, 21Connected to: GND 100%
VCCpin 4, 6Connected to: 5V 100%
  • Decoupling capacitor on 100% · 100 nF (12)
XTAL1/PB6pin 7Connected to: Not connected 50% · a signal 50%
  • Crystal on 50% · 20 MHz (1), 12 MHz (1)
  • Capacitor to GND on 50% · 8 pF (1), 22 pF (1)
XTAL2/PB7pin 8Connected to: Signal 67% · not connected 33%
  • Crystal on 50% · 20 MHz (1), 12 MHz (1)
  • Capacitor to GND on 50% · 8 pF (1), 22 pF (1)
PD6pin 10Connected to: Signal 67% · not connected 33%
  • Series resistor on 33% · 4.7 kΩ (3)
PB1pin 13Connected to: Signal 83% · not connected 17%
  • Series resistor on 33% · 220 Ω (1), 100 Ω (1)
PB2pin 14Connected to: Signal 83% · not connected 17%
  • Series resistor on 33% · 1 kΩ (1), 220 Ω (1)
PB5pin 17Connected to: A connector 83%
  • Series resistor on 33% · 2 kΩ (1), 220 Ω (1)
AVCCpin 18Connected to: 5V 50% · a signal 50%
  • Capacitor to GND on 100% · 100 nF (3), 4.7 µF (1)
  • Pull-up to 3V on 33% · 10 Ω (2)
ADC6pin 19Connected to: Not connected 67% · a signal 33%
  • Capacitor to GND on 33% · 100 nF (1), 10 pF (1)
AREFpin 20Connected to: Signal 50% · not connected 33% · 5V 17%
  • Capacitor to GND on 50% · 100 nF (2)
  • Pull-up to 1.24V on 33% · 100 Ω (1), 10 Ω (1)
ADC7pin 22Connected to: Not connected 67% · a signal 33%
  • Capacitor to GND on 33% · 100 nF (1), 10 pF (1)
PC0pin 23Connected to: Signal 100%
  • Series resistor on 67% · 680 Ω (1), 30 kΩ (1), 33 Ω (1)
  • Capacitor to GND on 33% · 100 nF (1), 10 pF (1)
PC1pin 24Connected to: Signal 100%
  • Series resistor on 67% · 4.7 kΩ (2), 30 kΩ (1), 33 Ω (1)
  • Resistor to GND on 33% · 4.7 kΩ (1), 10 kΩ (1)
  • Capacitor to GND on 33% · 100 nF (1), 10 pF (1)
PC2pin 25Connected to: Signal 83% · not connected 17%
  • Series resistor on 50% · 4.7 kΩ (2), 10 kΩ (1), 33 kΩ (1)
  • Capacitor to GND on 33% · 100 nF (1), 1 nF (1)
RESET/PC6pin 29Connected to: A connector 83%
  • Pull-up to 5V on 67% · 10 kΩ (4)
PD1pin 31Connected to: Signal 67% · not connected 33%
  • Series resistor on 50% · 1 kΩ (2), 33 Ω (1)
PD2pin 32Connected to: Signal 100%
  • Pull-up to 3V on 33% · 10 kΩ (1)
  • Series resistor on 33% · 10 kΩ (1), 100 Ω (1)

9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Brushless ESC by FordPrfkt, Continuity tester by vpatkov, Aircon control by lbrushmanl and Nanro uno by rmingon.

The ATmega88PA-A in open source designs

The gallery holds 7 open source boards using the ATmega88PA-A from 6 GitHub repositories; a typical one measures about 56.8 × 36 mm and carries around 37 components.

100% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.

The most starred is Brushless ESC by FordPrfkt.

Microcontrollers on boards using the ATmega88PA-A

What boards using the ATmega88PA-A are built for

ATmega88PA-A: common questions

Where can I find a ATmega88PA-A reference design?

Each of the 7 boards on this page is a real design using the ATmega88PA-A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ATmega88PA-A VCC pin?

The VCC pins have a decoupling capacitor on 6 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the ATmega88PA-A.

How is the ATmega88PA-A AVCC pin connected?

The AVCC pin has a capacitor to GND on 6 of 6 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 6 open source designs using the ATmega88PA-A.

What resistor goes on the ATmega88PA-A PC0 pin?

The PC0 pin has a series resistor on 4 of 6 designs, most often 680 Ω (then 30 kΩ). Counted from the KiCad layouts of 6 open source designs using the ATmega88PA-A.

Which microcontrollers do boards using the ATmega88PA-A use?

Most are built on AVR/Arduino (7).

How big is a typical board using the ATmega88PA-A?

The median is 56.8 × 36 mm, and 100% are two-layer designs.

What is the most popular open source board using the ATmega88PA-A?

By GitHub stars, Brushless ESC by FordPrfkt, with 3 stars.

Can I simulate one of these boards using the ATmega88PA-A before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part