13 open source boards using the ATtiny1604-SS
Real designs built with the ATtiny1604-SS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Hot Plate controller
c0pperdragon
60 × 100 mm25 parts2LNo license48AVR/Arduino
HDMI2SCART
c0pperdragon
40 × 27 mm19 parts4LNo license7AVR/Arduino
260321
McbeEringi
48 × 73 mm66 parts2LMIT2AVR/Arduino
Rcl
0x007E
52 × 52 mm73 parts2LCC-BY-NC-4.00AVR/Arduino
Vlt
0x007E
44.9 × 18.3 mm48 parts2LCC-BY-NC-4.00AVR/Arduino
Power control
portlandrobotics
20.3 × 28.6 mm23 parts2LSHL-2.110AVR/Arduino
Slim
McbeEringi
44 × 44 mm64 parts2LMIT2AVR/Arduino
Mb n boost
McbeEringi
100 × 86 mm60 parts2LMIT2AVR/Arduino
Serial usbc dip-7seg clk
McbeEringi
100 × 100 mm42 parts2LMIT2AVR/Arduino
Motor driver2026a
daisuke-ym
50 × 50 mm32 parts2LNo license0AVR/Arduino
Tx04-mx09
McbeEringi
99.1 × 96.5 mm17 parts2LMIT2AVR/Arduino
Tx04-pdfix
McbeEringi
91.1 × 88.9 mm17 parts2LMIT2AVR/Arduino
ATtiny
Tert2
86 × 77 mm11 parts2LNo license0
How designs wire the ATtiny1604-SS
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the ATtiny1604-SS connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 4.7 µF).
- The RESET/PA0 pin has a series resistor on 4 of 8 designs, most often 4.7 kΩ (then 470 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: 5V 100% |
|
| PA7pin 5 | Connected to: Signal 100% |
|
| RESET/PA0pin 10 | Connected to: A connector 63% |
|
| GNDpin 14 | Connected to: GND 100% | — |
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hot Plate controller by c0pperdragon, Power control by portlandrobotics, HDMI2SCART by c0pperdragon and 260321 by McbeEringi.
The ATtiny1604-SS in open source designs
The gallery holds 13 open source boards using the ATtiny1604-SS from 8 GitHub repositories; a typical one measures about 52 × 73 mm and carries around 32 components.
92% are two-layer designs, the rest use four layers or more, and 46% carry an open source license.
The most starred is Hot Plate controller by c0pperdragon.
Parts used alongside the ATtiny1604-SS
Microcontrollers on boards using the ATtiny1604-SS
What boards using the ATtiny1604-SS are built for
ATtiny1604-SS: common questions
Where can I find a ATtiny1604-SS reference design?
Each of the 13 boards on this page is a real design using the ATtiny1604-SS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ATtiny1604-SS VCC pin?
The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 8 open source designs using the ATtiny1604-SS.
What resistor goes on the ATtiny1604-SS RESET/PA0 pin?
The RESET/PA0 pin has a series resistor on 4 of 8 designs, most often 4.7 kΩ (then 470 Ω). Counted from the KiCad layouts of 8 open source designs using the ATtiny1604-SS.
Which microcontrollers do boards using the ATtiny1604-SS use?
Most are built on AVR/Arduino (13).
How big is a typical board using the ATtiny1604-SS?
The median is 52 × 73 mm, and 92% are two-layer designs.
What is the most popular open source board using the ATtiny1604-SS?
By GitHub stars, Hot Plate controller by c0pperdragon, with 48 stars.
Can I simulate one of these boards using the ATtiny1604-SS before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.