5 open source boards using the BGA725L6
Real designs built with the BGA725L6, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Black-Flipper
Broccoliux
142.1 × 143 mm206 parts4LNo license7LIV3F mikroBUS
mkmielke
25.4 × 42.9 mm31 parts4LNo license6Librem 5 Mainboard
gralco
74.3 × 65.6 mm1296 parts10LGPL-3.00Teseo liv3f breakout board
attexx
19 × 26.6 mm28 parts2LNo license0ESP32
MIDAS MK1
ISSUIUC
60 × 100 mm201 parts4LNo license31
How designs wire the BGA725L6
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the BGA725L6 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 1 nF (then 10 µF).
- The AI pin has a inductor on 4 of 5 designs, most often 5.6 nH (then 6.8 nH).
- The PON pin has a resistor to GND on 3 of 5 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| VCCpin 2 | Connected to: VCC_RF 100% |
|
| GNDRFpin 4 | Connected to: GND 100% | — |
| AIpin 5 | Connected to: Signal 100% |
|
| PONpin 6 | Connected to: TESEO-LIV3F 40% · not connected 20% · VDD33 20% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MIDAS MK1 by ISSUIUC, Black-Flipper by Broccoliux, LIV3F mikroBUS by mkmielke and Teseo liv3f breakout board by attexx.
The BGA725L6 in open source designs
The gallery holds 5 open source boards using the BGA725L6 from 5 GitHub repositories; a typical one measures about 60 × 65.6 mm and carries around 201 components.
80% use four copper layers or more, and 20% carry an open source license.
The most starred is MIDAS MK1 by ISSUIUC.
Parts used alongside the BGA725L6
Microcontrollers on boards using the BGA725L6
What boards using the BGA725L6 are built for
BGA725L6: common questions
Where can I find a BGA725L6 reference design?
Each of the 5 boards on this page is a real design using the BGA725L6. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the BGA725L6 VCC pin?
The VCC pin has a decoupling capacitor on 5 of 5 designs, most often 1 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the BGA725L6.
How is the BGA725L6 AI pin connected?
The AI pin has a inductor on 4 of 5 designs, most often 5.6 nH (then 6.8 nH). Counted from the KiCad layouts of 5 open source designs using the BGA725L6.
What resistor goes on the BGA725L6 PON pin?
The PON pin has a resistor to GND on 3 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the BGA725L6.
Which microcontrollers do boards using the BGA725L6 use?
Most are built on ESP32 (2).
How big is a typical board using the BGA725L6?
The median is 60 × 65.6 mm, and 20% are two-layer designs.
What is the most popular open source board using the BGA725L6?
By GitHub stars, MIDAS MK1 by ISSUIUC, with 31 stars.
Can I simulate one of these boards using the BGA725L6 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.