11 open source boards using the C14877
Real designs built with the C14877, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
CanBus-Radio-VAG
AugustoS97
39.9 × 45 mm28 parts2LNo license16AVR/Arduino
Halo
wyolum
243.8 × 66.3 mm152 parts2LApache-2.01AVR/Arduino
MIDIFAM
mikeyfarrow
29 × 86.6 mm72 parts2LNo license1STM32
PCB DRONE R8
ArduProject
102 × 49 mm150 parts4LMIT0AVR/Arduino
Workboy
dmang-dev
152 × 106.1 mm131 parts2LMIT0AVR/Arduino
RobotHat
aliaafee
65 × 63.5 mm40 parts2LNo license0AVR/Arduino
Arduino dolly
hollop90
26.8 × 53 mm37 parts4LNo license0AVR/Arduino
Programmer
benanderman
99.6 × 59.9 mm106 parts2LMIT59AVR/Arduino
Circuit
mikeyfarrow
29 × 86.6 mm57 parts2LNo license1AVR/Arduino
MotorDriver
aliaafee
56.3 × 43.5 mm33 parts2LNo license0AVR/Arduino
MotorDriver3
aliaafee
50 × 50 mm11 parts2LNo license0
How designs wire the C14877
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the C14877 connects to, and the resistors, capacitors and other passives placed on it.
- The RESET/PC6 pin has a pull-up to 5V on 7 of 8 designs, most often 10 kΩ (then 1 kΩ).
- The VCC pins have a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 4.7 µF).
- The XTAL1/PB6 pin has a capacitor to GND on 6 of 8 designs, most often 12 pF (then 18 pF).
- The XTAL2/PB7 pin has a capacitor to GND on 6 of 8 designs, most often 12 pF (then 18 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 3, 5, 21 | Connected to: GND 100% | — |
| VCCpin 4, 6 | Connected to: 5V 100% |
|
| XTAL1/PB6pin 7 | Connected to: Signal 100% |
|
| XTAL2/PB7pin 8 | Connected to: Signal 100% |
|
| PB5pin 17 | Connected to: A connector 100% |
|
| AVCCpin 18 | Connected to: 5V 100% |
|
| ADC6pin 19 | Connected to: Not connected 63% · a signal 38% | — |
| AREFpin 20 | Connected to: Signal 63% · 5V 25% |
|
| ADC7pin 22 | Connected to: Not connected 63% · a signal 38% | — |
| PC4pin 27 | Connected to: A connector 50% |
|
| PC5pin 28 | Connected to: A connector 50% |
|
| RESET/PC6pin 29 | Connected to: A connector 100% |
|
17 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Programmer by benanderman, CanBus-Radio-VAG by AugustoS97, Circuit by mikeyfarrow and Halo by wyolum.
The C14877 in open source designs
The gallery holds 11 open source boards using the C14877 from 8 GitHub repositories; a typical one measures about 56.3 × 59.9 mm and carries around 57 components.
82% are two-layer designs, the rest use four layers or more, and 36% carry an open source license.
The most starred is Programmer by benanderman.
Parts used alongside the C14877
Microcontrollers on boards using the C14877
What boards using the C14877 are built for
C14877: common questions
Where can I find a C14877 reference design?
Each of the 11 boards on this page is a real design using the C14877. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the C14877 RESET/PC6 pin?
The RESET/PC6 pin has a pull-up to 5V on 7 of 8 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 8 open source designs using the C14877.
What decoupling capacitors do designs use on the C14877 VCC pin?
The VCC pins have a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 8 open source designs using the C14877.
How is the C14877 XTAL1/PB6 pin connected?
The XTAL1/PB6 pin has a capacitor to GND on 6 of 8 designs, most often 12 pF (then 18 pF). Counted from the KiCad layouts of 8 open source designs using the C14877.
Which microcontrollers do boards using the C14877 use?
Most are built on AVR/Arduino (10) and STM32 (1).
How big is a typical board using the C14877?
The median is 56.3 × 59.9 mm, and 82% are two-layer designs.
What is the most popular open source board using the C14877?
By GitHub stars, Programmer by benanderman, with 59 stars.
Can I simulate one of these boards using the C14877 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.