6 open source boards using the C7955

Real designs built with the C7955, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the C7955

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the C7955 connects to, and the resistors, capacitors and other passives placed on it.

  • The NRST pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ (then 1.2 kΩ).
  • The VBAT pin has a pull-up to 3.3V on 4 of 5 designs, most often 1.2 kΩ (then 10 kΩ).
  • The + pins have a series resistor on 4 of 5 designs, most often 1.5 kΩ (then 11 Ω).
  • The - pins have a series resistor on 3 of 5 designs, most often 11 Ω (then 4.7 kΩ).
VBATpin 1Connected to: A connector 60% · 3.3V 20%
  • Pull-up to 3.3V on 80% · 1.2 kΩ (2), 10 kΩ (1), 2.2 kΩ (1)
-pin 2, 6Connected to: C7593 20%
  • Series resistor on 60% · 11 Ω (4), 4.7 kΩ (2)
  • Pull-up to 3.3V on 40% · 1.8 kΩ (4)
  • Capacitor to GND on 40% · 1.5 nF (2)
+pin 3, 5Connected to: A connector 20%
  • Series resistor on 80% · 1.5 kΩ (6), 11 Ω (4), 10 kΩ (3)
  • Resistor to GND on 60% · 1.5 kΩ (2), 51 kΩ (2), 10 kΩ (1)
V-pin 4Connected to: GND 60% · a signal 40%
NRSTpin 7Connected to: A connector 80%
  • Pull-up to 3.3V on 100% · 10 kΩ (2), 1.2 kΩ (2), 2.2 kΩ (1)
V+pin 8Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 60% · 100 nF (3), 10 µF (2)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Gdoor by gdoor-org, SAO CORE4 by ageppert, Core-64c-Compact-Interactive-Core-Memory-Badge by ageppert and Analog to pwm by adeboni.

The C7955 in open source designs

The gallery holds 6 open source boards using the C7955 from 5 GitHub repositories; a typical one measures about 67.9 × 87 mm and carries around 96 components.

50% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.

The most starred is Gdoor by gdoor-org.

Parts used alongside the C7955

Microcontrollers on boards using the C7955

C7955: common questions

Where can I find a C7955 reference design?

Each of the 6 boards on this page is a real design using the C7955. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the C7955 NRST pin?

The NRST pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ (then 1.2 kΩ). Counted from the KiCad layouts of 5 open source designs using the C7955.

What pull-up resistor is used on the C7955 VBAT pin?

The VBAT pin has a pull-up to 3.3V on 4 of 5 designs, most often 1.2 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the C7955.

What resistor goes on the C7955 + pin?

The + pins have a series resistor on 4 of 5 designs, most often 1.5 kΩ (then 11 Ω). Counted from the KiCad layouts of 5 open source designs using the C7955.

Which microcontrollers do boards using the C7955 use?

Most are built on ESP32 (1) and STM32 (1).

How big is a typical board using the C7955?

The median is 67.9 × 87 mm, and 50% are two-layer designs.

What is the most popular open source board using the C7955?

By GitHub stars, Gdoor by gdoor-org, with 56 stars.

Can I simulate one of these boards using the C7955 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part