9 open source boards using the CAT24C128
Real designs built with the CAT24C128, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Arduino ads129x
OpenElectronicsLab
197 × 71 mm267 partsGPL-3.0102STM32
Node base
LanternD
78 × 40 mm73 parts2LApache-2.06Raspberry Pi
Tinyfpga raspi romi board
hbrc-fpga-class
103.4 × 121.9 mm71 parts2LNo license3RP2040/RP2350
GPSDO
pwengel
97.4 × 75.4 mm115 parts2LNo license2AVR/Arduino
Incubator
MariwanJ
124 × 70.2 mm42 parts2LGPL-3.01AVR/Arduino
Full Circuit
EthanSousaProjects
110 × 110 mm72 parts2LGPL-3.00AVR/Arduino
Patch shield digital
OpenElectronicsLab
197 × 71 mm77 partsGPL-3.0102Raspberry Pi
Rpi hat
ppetr
65 × 56.5 mm22 parts2LApache-2.02Raspberry Pi
Raspberry pi hat
ClubRobotInsat
65 × 56.5 mm23 parts2LApache-2.00
How designs wire the CAT24C128
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the CAT24C128 connects to, and the resistors, capacitors and other passives placed on it.
- The A1 pin is tied to GND on 8 of 8 designs.
- The A0 pin is tied to GND on 7 of 8 designs.
- The A2 pin is tied to GND on 7 of 8 designs.
- The SDA pin has a pull-up to 3.3V on 5 of 8 designs, most often 3.9 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A0pin 1 | Connected to: GND 88% | — |
| A1pin 2 | Connected to: GND 100% | — |
| A2pin 3 | Connected to: GND 88% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| SDApin 5 | Connected to: A connector 75%, the microcontroller 50% |
|
| SCLpin 6 | Connected to: A connector 75%, the microcontroller 50% |
|
| WPpin 7 | Connected to: GND 50% · a signal 50% |
|
| VCCpin 8 | Connected to: 3.3V 75% · a signal 25% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Arduino ads129x by OpenElectronicsLab, Node base by LanternD, Tinyfpga raspi romi board by hbrc-fpga-class and Rpi hat by ppetr.
The CAT24C128 in open source designs
The gallery holds 9 open source boards using the CAT24C128 from 8 GitHub repositories; a typical one measures about 103.4 × 71 mm and carries around 72 components.
100% are two-layer designs, the rest use four layers or more, and 78% carry an open source license.
The most starred is Arduino ads129x by OpenElectronicsLab.
Microcontrollers on boards using the CAT24C128
What boards using the CAT24C128 are built for
CAT24C128: common questions
Where can I find a CAT24C128 reference design?
Each of the 9 boards on this page is a real design using the CAT24C128. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the CAT24C128 A1 pin connected?
The A1 pin is tied to GND on 8 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the CAT24C128.
How is the CAT24C128 A0 pin connected?
The A0 pin is tied to GND on 7 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the CAT24C128.
How is the CAT24C128 A2 pin connected?
The A2 pin is tied to GND on 7 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the CAT24C128.
Which microcontrollers do boards using the CAT24C128 use?
Most are built on AVR/Arduino (4), Raspberry Pi (3), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the CAT24C128?
The median is 103.4 × 71 mm, and 100% are two-layer designs.
What is the most popular open source board using the CAT24C128?
By GitHub stars, Arduino ads129x by OpenElectronicsLab, with 102 stars.
Can I simulate one of these boards using the CAT24C128 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.