8 open source boards using the CJ431
Real designs built with the CJ431, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Toolbox
StudioKAT
80.9 × 128.5 mm272 parts2LNo license11FlippyDriver
NietoSkunk
189.4 × 59.1 mm310 parts4LMIT10DualTimbre
StudioKAT
82 × 100 mm132 parts2LNo license7VintageDualVCA
StudioKAT
40.3 × 128.5 mm95 parts2LNo license5Milliohm meter
gabeak2
59.7 × 54.6 mm32 parts4LGPL-3.03ESP32
Lfp
maxakash
216 × 146 mm831 parts2LNo license0Stm32f4 uno poe
easy-smart
68.6 × 53.3 mm81 parts2LNo license0Ksoloti gills cv expander
ksoloti
64 × 20.5 mm49 parts2LCC-BY-4.02
How designs wire the CJ431
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the CJ431 connects to, and the resistors, capacitors and other passives placed on it.
- The REF pin has a series resistor on 5 of 8 designs, most often 10 kΩ (then 47 kΩ).
- The A pin is tied to GND on 6 of 8 designs (a signal on 2).
- The K pin has a series resistor on 4 of 8 designs, most often 10 kΩ (then 100 kΩ).
- The K pin has a pull-up to 12V on 4 of 8 designs, most often 1 kΩ (then 220 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| REFpin 1 | Connected to: Signal 63% · 2.5V 25% |
|
| Kpin 2 | Connected to: Signal 50% · GND 25% · 2.5V 25% |
|
| Apin 3 | Connected to: GND 75% · a signal 25% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Toolbox by StudioKAT, FlippyDriver by NietoSkunk, DualTimbre by StudioKAT and VintageDualVCA by StudioKAT.
The CJ431 in open source designs
The gallery holds 8 open source boards using the CJ431 from 8 GitHub repositories; a typical one measures about 74.7 × 79.5 mm and carries around 114 components.
75% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Toolbox by StudioKAT.
Parts used alongside the CJ431
Microcontrollers on boards using the CJ431
What boards using the CJ431 are built for
CJ431: common questions
Where can I find a CJ431 reference design?
Each of the 8 boards on this page is a real design using the CJ431. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the CJ431 REF pin?
The REF pin has a series resistor on 5 of 8 designs, most often 10 kΩ (then 47 kΩ). Counted from the KiCad layouts of 8 open source designs using the CJ431.
How is the CJ431 A pin connected?
The A pin is tied to GND on 6 of 8 designs (a signal on 2). Counted from the KiCad layouts of 8 open source designs using the CJ431.
What resistor goes on the CJ431 K pin?
The K pin has a series resistor on 4 of 8 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 8 open source designs using the CJ431.
Which microcontrollers do boards using the CJ431 use?
Most are built on ESP32 (1).
How big is a typical board using the CJ431?
The median is 74.7 × 79.5 mm, and 75% are two-layer designs.
What is the most popular open source board using the CJ431?
By GitHub stars, Toolbox by StudioKAT, with 11 stars.
Can I simulate one of these boards using the CJ431 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.