6 open source boards using the DG408
Real designs built with the DG408, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Goodfet
travisgoodspeed
84 × 82 mm234 parts4LNo license333Tap o matic
cormallen
120.7 × 108 mm64 parts2LCC-BY-NC-4.011Analog board
minisystem
200 × 150 mm500 parts2LNo license3AVR/Arduino
Titan67j60
Lehman3065
191 × 123 mm242 parts2LNo license0PIC
RE3RT4Prog
afiglee
130 × 100 mm68 parts2LNo license0Acoustic research
svenclawdbot-ai
100 × 80 mm25 parts4LNo license0
How designs wire the DG408
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the DG408 connects to, and the resistors, capacitors and other passives placed on it.
- The V+ pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 1 µF).
- The V- pin has a decoupling capacitor on 2 of 5 designs, most often 100 nF.
- The S1 pin has a series resistor on 2 of 5 designs, most often 0 Ω (then 39 kΩ).
- The S2 pin has a series resistor on 2 of 5 designs, most often 0 Ω (then 39 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| V-pin 3 | Connected to: GND 40% · -12V 40% · a signal 20% |
|
| S1pin 4 | Connected to: A connector 40% |
|
| S2pin 5 | Connected to: A connector 40% |
|
| S3pin 6 | Connected to: A connector 40% |
|
| V+pin 13 | Connected to: 12V 60% · a signal 40% |
|
| GNDpin 14 | Connected to: GND 100% | — |
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Goodfet by travisgoodspeed, Tap o matic by cormallen, Analog board by minisystem and RE3RT4Prog by afiglee.
The DG408 in open source designs
The gallery holds 6 open source boards using the DG408 from 6 GitHub repositories; a typical one measures about 125.3 × 104 mm and carries around 151 components.
67% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is Goodfet by travisgoodspeed.
Parts used alongside the DG408
Microcontrollers on boards using the DG408
What boards using the DG408 are built for
DG408: common questions
Where can I find a DG408 reference design?
Each of the 6 boards on this page is a real design using the DG408. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the DG408 V+ pin?
The V+ pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the DG408.
What decoupling capacitors do designs use on the DG408 V- pin?
The V- pin has a decoupling capacitor on 2 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the DG408.
What resistor goes on the DG408 S1 pin?
The S1 pin has a series resistor on 2 of 5 designs, most often 0 Ω (then 39 kΩ). Counted from the KiCad layouts of 5 open source designs using the DG408.
Which microcontrollers do boards using the DG408 use?
Most are built on AVR/Arduino (1) and PIC (1).
How big is a typical board using the DG408?
The median is 125.3 × 104 mm, and 67% are two-layer designs.
What is the most popular open source board using the DG408?
By GitHub stars, Goodfet by travisgoodspeed, with 333 stars.
Can I simulate one of these boards using the DG408 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.