9 open source boards using the DS3232M
Real designs built with the DS3232M, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Orbigator
wyolum
70 × 56 mm23 parts2LNo license17LC PAMV4b
WMXZ-EU
91 × 22 mm63 parts4LMIT8ESP32
Worldclockv1
orri93
193.8 × 120 mm116 parts2LMIT1AVR/Arduino
IV6Clock2 base
SarahAlroe
99.1 × 45.7 mm36 parts2LNo license1Raspberry Pi
Piridium bus
Alan-JH
90.2 × 95.9 mm156 parts4LCC-BY-NC-4.00AVR/Arduino
Mobile Monitor Redesign
deogratius2phantom
49 × 39.1 mm90 parts4LNo license0ESP32
Esp32-stereo audio recorder
Harshad-vali
62.5 × 44 mm45 parts2LNo license0ESP32
Test Rocket Board
colin-skinner
68 × 66 mm79 parts2LNo license0ESP32
Actuator Board V1
colin-skinner
53.8 × 29.2 mm19 parts2LNo license0
How designs wire the DS3232M
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the DS3232M connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 10 µF).
- The 32KHZ pin is left unconnected on 7 of 8 designs.
- The SDA pin has a pull-up to 3.3V on 5 of 8 designs, most often 10 kΩ (then 20 kΩ).
- The SCL pin has a pull-up to 3.3V on 5 of 8 designs, most often 10 kΩ (then 20 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 32KHZpin 1 | Connected to: Not connected 88% | — |
| VCCpin 2 | Connected to: 3.3V 75% |
|
| GNDpin 5 | Connected to: GND 89% | — |
| VBATpin 6 | Connected to: VBAT 63% · a signal 38% | — |
| SDApin 7 | Connected to: The microcontroller 75%, a connector 25% |
|
| SCLpin 8 | Connected to: The microcontroller 75%, a connector 25% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Orbigator by wyolum, LC PAMV4b by WMXZ-EU, Worldclockv1 by orri93 and IV6Clock2 base by SarahAlroe.
The DS3232M in open source designs
The gallery holds 9 open source boards using the DS3232M from 8 GitHub repositories; a typical one measures about 70 × 45.7 mm and carries around 63 components.
67% are two-layer designs, the rest use four layers or more, and 22% carry an open source license.
The most starred is Orbigator by wyolum.
Microcontrollers on boards using the DS3232M
What boards using the DS3232M are built for
DS3232M: common questions
Where can I find a DS3232M reference design?
Each of the 9 boards on this page is a real design using the DS3232M. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the DS3232M VCC pin?
The VCC pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the DS3232M.
How is the DS3232M 32KHZ pin connected?
The 32KHZ pin is left unconnected on 7 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the DS3232M.
What pull-up resistor is used on the DS3232M SDA pin?
The SDA pin has a pull-up to 3.3V on 5 of 8 designs, most often 10 kΩ (then 20 kΩ). Counted from the KiCad layouts of 8 open source designs using the DS3232M.
Which microcontrollers do boards using the DS3232M use?
Most are built on ESP32 (4), AVR/Arduino (2), Raspberry Pi (1) and RP2040/RP2350 (1).
How big is a typical board using the DS3232M?
The median is 70 × 45.7 mm, and 67% are two-layer designs.
What is the most popular open source board using the DS3232M?
By GitHub stars, Orbigator by wyolum, with 17 stars.
Can I simulate one of these boards using the DS3232M before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.