7 open source boards using the ESP-07

Real designs built with the ESP-07, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the ESP-07

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ESP-07 connects to, and the resistors, capacitors and other passives placed on it.

  • The EN pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ (then 10 Ω).
  • The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 10 µF).
  • The GPIO15 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ.
  • The RST pin has a pull-up to 3.3V on 3 of 6 designs, most often 10 kΩ.
RSTpin 1Connected to: The microcontroller 33%
  • Pull-up to 3.3V on 50% · 10 kΩ (3)
  • Series resistor on 33% · 0 Ω (1), 100 Ω (1)
ADCpin 2Connected to: Not connected 50% · a signal 50%
  • Resistor to GND on 33% · 100 Ω (1), 100 kΩ (1)
  • Pull-up to 3.3V on 33% · 10 kΩ (1), 330 kΩ (1)
ENpin 3Connected to: The microcontroller 33%
  • Pull-up to 3.3V on 83% · 10 kΩ (4), 10 Ω (1)
GPIO16pin 4Connected to: Not connected 50% · a signal 50%
  • Series resistor on 33% · 0 Ω (1), 100 Ω (1)
VCCpin 8Connected to: 3.3V 100%
  • Decoupling capacitor on 83% · 100 nF (4), 10 µF (2), 10 nF (1)
GNDpin 9Connected to: GND 100%
GPIO15pin 10Connected to: Signal 80% · GND 20%
  • Resistor to GND on 80% · 10 kΩ (4)
GPIO2pin 11Connected to: A connector 57%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
GPIO0pin 12Connected to: A connector 43%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
GPIO5pin 14Connected to: Not connected 50% · a signal 50%
  • Pull-up to 3.3V on 33% · 10 kΩ (1), 4.7 kΩ (1)
GPIO3/RXDpin 15Connected to: A connector 57%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
  • Series resistor on 33% · 1 kΩ (1)
GPIO1/TXDpin 16Connected to: A connector 57%
  • Series resistor on 33% · 1 kΩ (1), 10 kΩ (1)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Noah hardware by GonzaCerv, Kicad p1-port thingie by ehjortberg, Esp8266-tiny breakout board by ezcGman and Power tracking heaterP by kwiecinski.

The ESP-07 in open source designs

The gallery holds 7 open source boards using the ESP-07 from 6 GitHub repositories; a typical one measures about 98 × 49 mm and carries around 74 components.

100% are two-layer designs, the rest use four layers or more, and 71% carry an open source license.

The most starred is Noah hardware by GonzaCerv.

Parts used alongside the ESP-07

Microcontrollers on boards using the ESP-07

ESP-07: common questions

Where can I find a ESP-07 reference design?

Each of the 7 boards on this page is a real design using the ESP-07. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP-07 EN pin?

The EN pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ (then 10 Ω). Counted from the KiCad layouts of 6 open source designs using the ESP-07.

What decoupling capacitors do designs use on the ESP-07 VCC pin?

The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 6 open source designs using the ESP-07.

What resistor goes on the ESP-07 GPIO15 pin?

The GPIO15 pin has a resistor to GND on 4 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the ESP-07.

Which microcontrollers do boards using the ESP-07 use?

Most are built on ESP8266 (3) and STM32 (2).

How big is a typical board using the ESP-07?

The median is 98 × 49 mm, and 100% are two-layer designs.

What is the most popular open source board using the ESP-07?

By GitHub stars, Noah hardware by GonzaCerv, with 28 stars.

Can I simulate one of these boards using the ESP-07 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part