7 open source boards using the ESP-12S
Real designs built with the ESP-12S, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Raesp gateway
cziter15
47 × 33 mm17 parts4LGPL-3.011ESP8266
UnderControl Hardware Design
YamanSeyravan
100 × 100 mm185 parts4LGPL-3.02ESP8266
Nestbox v2
Octanis3
85 × 60 mm113 parts2LMIT2ESP8266
Wallbox board
dkonigsberg
118.8 × 86.4 mm50 parts2LCC-BY-SA-4.01ESP8266
Avalon communication board
AvalonROV
100 × 62.1 mm115 parts2LNo license0ESP8266
Esp12s aq hw
subraizada3
37.1 × 36.8 mm19 parts2LNo license0ESP8266
Enocean switch
M-o-a-T
43.3 × 67.3 mm18 parts2LNo license0
How designs wire the ESP-12S
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ESP-12S connects to, and the resistors, capacitors and other passives placed on it.
- The ADC pin is left unconnected on 5 of 6 designs.
- The IO16 pin is left unconnected on 4 of 6 designs (a signal on 2).
- The IO14 pin has a series resistor on 3 of 6 designs, most often 1.5 kΩ (then 1 kΩ).
- The IO0 pin has a series resistor on 3 of 7 designs, most often 1 kΩ (then 220 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADCpin 2 | Connected to: Not connected 83% · a signal 17% | — |
| IO16pin 4 | Connected to: Not connected 67% · a signal 33% | — |
| IO14pin 5 | Connected to: Signal 83% · not connected 17% |
|
| VCCpin 8 | Connected to: 3.3V 86% | — |
| GNDpin 9 | Connected to: GND 100% | — |
| IO0pin 12 | Connected to: A connector 57% |
|
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Raesp gateway by cziter15, Nestbox v2 by Octanis3, UnderControl Hardware Design by YamanSeyravan and Wallbox board by dkonigsberg.
The ESP-12S in open source designs
The gallery holds 7 open source boards using the ESP-12S from 7 GitHub repositories; a typical one measures about 85 × 62.1 mm and carries around 50 components.
71% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is Raesp gateway by cziter15.
Parts used alongside the ESP-12S
Microcontrollers on boards using the ESP-12S
What boards using the ESP-12S are built for
ESP-12S: common questions
Where can I find a ESP-12S reference design?
Each of the 7 boards on this page is a real design using the ESP-12S. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP-12S ADC pin connected?
The ADC pin is left unconnected on 5 of 6 designs. Counted from the KiCad layouts of 7 open source designs using the ESP-12S.
How is the ESP-12S IO16 pin connected?
The IO16 pin is left unconnected on 4 of 6 designs (a signal on 2). Counted from the KiCad layouts of 7 open source designs using the ESP-12S.
What resistor goes on the ESP-12S IO14 pin?
The IO14 pin has a series resistor on 3 of 6 designs, most often 1.5 kΩ (then 1 kΩ). Counted from the KiCad layouts of 7 open source designs using the ESP-12S.
Which microcontrollers do boards using the ESP-12S use?
Most are built on ESP8266 (7).
How big is a typical board using the ESP-12S?
The median is 85 × 62.1 mm, and 71% are two-layer designs.
What is the most popular open source board using the ESP-12S?
By GitHub stars, Raesp gateway by cziter15, with 11 stars.
Can I simulate one of these boards using the ESP-12S before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.