5 open source boards using the ESP32-S3-WROOM-1-N4R8

Real designs built with the ESP32-S3-WROOM-1-N4R8, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the ESP32-S3-WROOM-1-N4R8

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the ESP32-S3-WROOM-1-N4R8 connects to, and the resistors, capacitors and other passives placed on it.

  • The EN pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ.
  • The IO35 pin is left unconnected on 5 of 5 designs.
  • The IO11 pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ.
  • The IO0 pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ.
GNDpin 1, 40, 41Connected to: GND 100%
3V3pin 2Connected to: 3.3V 80% · a signal 20%
ENpin 3Connected to: Signal 100%
  • Pull-up to 3.3V on 100% · 10 kΩ (5)
  • Capacitor to GND on 60% · 1 µF (2), 100 nF (1)
IO5pin 5Connected to: A connector 40%
  • Series resistor on 40% · 320 Ω (1), 4.7 Ω (1)
IO6pin 6Connected to: A connector 40%
  • Series resistor on 40% · 320 Ω (1), 10 kΩ (1)
IO15pin 8Connected to: Signal 100%
  • Resistor to GND on 40% · 10 kΩ (2)
IO10pin 18Connected to: Signal 60% · not connected 40%
  • Pull-up to VCC_P on 60% · 10 kΩ (3)
IO11pin 19Connected to: Signal 80% · not connected 20%
  • Pull-up to 3.3V on 80% · 10 kΩ (4)
IO12pin 20Connected to: Signal 80% · not connected 20%
  • Pull-up to 3.3V on 60% · 10 kΩ (3)
IO0pin 27Connected to: Signal 100%
  • Pull-up to 3.3V on 80% · 10 kΩ (4)
IO35pin 28Connected to: Not connected 100%
IO36pin 29Connected to: Not connected 80% · a signal 20%
IO37pin 30Connected to: Not connected 80% · a signal 20%
IO38pin 31Connected to: Signal 60% · not connected 40%
  • Pull-up to VCC_P on 40% · 10 kΩ (1), 4.7 kΩ (1)
IO2pin 38Connected to: Signal 100%
  • Series resistor on 40% · 56 kΩ (2), 100 Ω (1)
IO1pin 39Connected to: Not connected 60% · a signal 40%

23 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hoerbaer by drachosaurus, TyphoonMotherboard rev1 KiCad by hpvdt, ADVdash 5" by ADVecu and Split keyboard by garvita4.

The ESP32-S3-WROOM-1-N4R8 in open source designs

The gallery holds 5 open source boards using the ESP32-S3-WROOM-1-N4R8 from 5 GitHub repositories; a typical one measures about 76 × 88 mm and carries around 148 components.

60% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.

The most starred is Hoerbaer by drachosaurus.

Microcontrollers on boards using the ESP32-S3-WROOM-1-N4R8

What boards using the ESP32-S3-WROOM-1-N4R8 are built for

ESP32-S3-WROOM-1-N4R8: common questions

Where can I find a ESP32-S3-WROOM-1-N4R8 reference design?

Each of the 5 boards on this page is a real design using the ESP32-S3-WROOM-1-N4R8. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP32-S3-WROOM-1-N4R8 EN pin?

The EN pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the ESP32-S3-WROOM-1-N4R8.

How is the ESP32-S3-WROOM-1-N4R8 IO35 pin connected?

The IO35 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the ESP32-S3-WROOM-1-N4R8.

What pull-up resistor is used on the ESP32-S3-WROOM-1-N4R8 IO11 pin?

The IO11 pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the ESP32-S3-WROOM-1-N4R8.

Which microcontrollers do boards using the ESP32-S3-WROOM-1-N4R8 use?

Most are built on ESP32 (5).

How big is a typical board using the ESP32-S3-WROOM-1-N4R8?

The median is 76 × 88 mm, and 60% are two-layer designs.

What is the most popular open source board using the ESP32-S3-WROOM-1-N4R8?

By GitHub stars, Hoerbaer by drachosaurus, with 1 stars.

Can I simulate one of these boards using the ESP32-S3-WROOM-1-N4R8 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part