6 open source boards using the ESP32-WROVER-B

Real designs built with the ESP32-WROVER-B, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the ESP32-WROVER-B

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ESP32-WROVER-B connects to, and the resistors, capacitors and other passives placed on it.

  • The EN pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ (then 4.7 kΩ).
  • The EN pin has a capacitor to GND on 6 of 6 designs, most often 1 µF (then 100 nF).
  • The IO9 pin is left unconnected on 6 of 6 designs.
  • The IO10 pin is left unconnected on 6 of 6 designs.
GNDpin 1, 15, 38Connected to: GND 89%
3.3Vpin 2Connected to: 3.3V 83% · a signal 17%
ENpin 3Connected to: Signal 100%
  • Pull-up to 3.3V on 100% · 10 kΩ (4), 4.7 kΩ (2)
  • Capacitor to GND on 100% · 1 µF (2), 100 nF (2)
IO36pin 4Connected to: Signal 83% · not connected 17%
  • Capacitor to GND on 50% · 1 µF (1)
  • Series capacitor on 50%
  • Resistor to GND on 50% · 4.7 kΩ (3)
  • Pull-up to 3.3V on 50% · 4.7 kΩ (3)
IO35pin 7Connected to: A connector 67%
  • Pull-up to 3.3V on 67% · 4.7 kΩ (3), 10 kΩ (1)
IO32pin 8Connected to: A connector 83%
  • Pull-up to 3.3V on 50% · 2 kΩ (3)
IO33pin 9Connected to: A connector 83%
  • Pull-up to 3.3V on 50% · 2 kΩ (3)
IO25pin 10Connected to: A connector 67%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
  • Series resistor on 33% · 270 Ω (1), 100 Ω (1)
IO13pin 16Connected to: Signal 83% · not connected 17%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
IO9pin 17Connected to: Not connected 100%
IO10pin 18Connected to: Not connected 100%
IO11pin 19Connected to: Not connected 100%
IO6pin 20Connected to: Not connected 100%
IO7pin 21Connected to: Not connected 100%
IO8pin 22Connected to: Not connected 100%
IO15pin 23Connected to: A connector 67%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
IO0pin 25Connected to: Signal 100%
  • Pull-up to 3.3V on 50% · 4.7 kΩ (3)
IO4pin 26Connected to: A connector 33% · not connected 17%
  • Pull-up to 3.3V on 33% · 4.7 kΩ (1), 10 kΩ (1)
NCpin 27, 28, 32Connected to: Not connected 100%
IO21pin 33Connected to: A connector 50%
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
Pin 39Connected to: Not connected 60% · GND 40%

14 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include NextTRS by apuder, PocketTRS by apuder, Dual button doorbell by espena and Turpial hardware by btcven.

The ESP32-WROVER-B in open source designs

The gallery holds 6 open source boards using the ESP32-WROVER-B from 6 GitHub repositories; a typical one measures about 113.8 × 82.7 mm and carries around 82 components.

67% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.

The most starred is NextTRS by apuder.

Parts used alongside the ESP32-WROVER-B

Microcontrollers on boards using the ESP32-WROVER-B

What boards using the ESP32-WROVER-B are built for

ESP32-WROVER-B: common questions

Where can I find a ESP32-WROVER-B reference design?

Each of the 6 boards on this page is a real design using the ESP32-WROVER-B. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP32-WROVER-B EN pin?

The EN pin has a pull-up to 3.3V on 6 of 6 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the ESP32-WROVER-B.

How is the ESP32-WROVER-B IO9 pin connected?

The IO9 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ESP32-WROVER-B.

How is the ESP32-WROVER-B IO10 pin connected?

The IO10 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ESP32-WROVER-B.

Which microcontrollers do boards using the ESP32-WROVER-B use?

Most are built on ESP32 (6).

How big is a typical board using the ESP32-WROVER-B?

The median is 113.8 × 82.7 mm, and 67% are two-layer designs.

What is the most popular open source board using the ESP32-WROVER-B?

By GitHub stars, NextTRS by apuder, with 74 stars.

Can I simulate one of these boards using the ESP32-WROVER-B before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part