6 open source boards using the INA826

Real designs built with the INA826, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the INA826

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the INA826 connects to, and the resistors, capacitors and other passives placed on it.

  • The RG pins have a series resistor on 5 of 5 designs, most often 100 Ω (then 487 Ω).
  • The VS+ pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
  • The VS- pin is tied to GND on 4 of 5 designs.
  • The - pin has a series resistor on 3 of 5 designs, most often 147 kΩ (then 330 Ω).
-pin 1Connected to: Signal 100%
  • Series resistor on 60% · 147 kΩ (1), 330 Ω (1), 250 mΩ (1)
  • Resistor to GND on 40% · 1 kΩ (1), 1 MΩ (1)
  • Series capacitor on 40% · 470 nF (1)
RGpin 2, 3Connected to: Signal 100%
  • Series resistor on 100% · 100 Ω (2), 487 Ω (2)
+pin 4Connected to: Signal 100%
  • Series resistor on 60% · 147 kΩ (1), 330 Ω (1), 250 mΩ (1)
  • Series capacitor on 60% · 470 nF (1), 100 pF (1)
  • Resistor to GND on 40% · 1 kΩ (1), 1 MΩ (1)
VS-pin 5Connected to: GND 80% · -15V 20%
VS+pin 8Connected to: 3.3V 80% · a signal 20%
  • Decoupling capacitor on 80% · 100 nF (4), 10 µF (1)

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include GDI-STM by rusefi, Panel board by ReflexCreations, ONLY ECG fix by tregatti-tech and I2c pancake by waterloo-rocketry.

The INA826 in open source designs

The gallery holds 6 open source boards using the INA826 from 5 GitHub repositories; a typical one measures about 121.5 × 140.6 mm and carries around 172 components.

50% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.

The most starred is GDI-STM by rusefi.

Microcontrollers on boards using the INA826

What boards using the INA826 are built for

INA826: common questions

Where can I find a INA826 reference design?

Each of the 6 boards on this page is a real design using the INA826. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the INA826 RG pin?

The RG pins have a series resistor on 5 of 5 designs, most often 100 Ω (then 487 Ω). Counted from the KiCad layouts of 5 open source designs using the INA826.

What decoupling capacitors do designs use on the INA826 VS+ pin?

The VS+ pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the INA826.

How is the INA826 VS- pin connected?

The VS- pin is tied to GND on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the INA826.

Which microcontrollers do boards using the INA826 use?

Most are built on STM32 (2), ESP32 (1), NXP (1) and PIC (1).

How big is a typical board using the INA826?

The median is 121.5 × 140.6 mm, and 50% are two-layer designs.

What is the most popular open source board using the INA826?

By GitHub stars, GDI-STM by rusefi, with 48 stars.

Can I simulate one of these boards using the INA826 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part