11 open source boards using the LM317_3PinPackage
Real designs built with the LM317_3PinPackage, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Actidamp mk4-smd
josko7452
119 × 100 mm199 parts4LNo license1STM32
Scot resolver
philcrump
108.6 × 79.4 mm137 parts2LMIT1PIC
Hp dl380 fan controller
mschaf
100 × 35 mm62 parts2LNo license0SnackBus PSU
coriolisinstruments
99 × 87 mm34 parts2LNo license33AVR/Arduino
FM radio atmega 8
411568
77.5 × 52.1 mm19 parts2LMIT3Back power board
limblab
44.2 × 45.5 mm14 parts2LNo license2PSUCompanion
coriolisinstruments
38.5 × 81 mm19 parts2LNo license33Microchip SAM
Same70
brengi
62.5 × 87.5 mm67 parts2LNo license7AVR/Arduino
Transistor matcher
rabidaudio
14 parts2LMIT31PT100
MyCloudExample
100 × 100 mm17 parts2LNo license1Backup r1
blthree
99.4 × 78 mm62 parts2LNo license0
How designs wire the LM317_3PinPackage
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the LM317_3PinPackage connects to, and the resistors, capacitors and other passives placed on it.
- The ADJ pin has a resistor to GND on 7 of 9 designs, most often 1 kΩ (then 220 Ω).
- The ADJ pin has a pull-up to 5V on 6 of 9 designs, most often 330 Ω (then 220 Ω).
- The VI pin has a decoupling capacitor on 4 of 9 designs, most often 220 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJpin 1 | Connected to: Signal 100% |
|
| VOpin 2 | Connected to: 5V 67% · a signal 33% | — |
| VIpin 3 | Connected to: 12V 56% · a signal 44% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PSUCompanion by coriolisinstruments, Transistor matcher by rabidaudio, Same70 by brengi and FM radio atmega 8 by 411568.
The LM317_3PinPackage in open source designs
The gallery holds 11 open source boards using the LM317_3PinPackage from 10 GitHub repositories; a typical one measures about 99.2 × 80.2 mm and carries around 34 components.
91% are two-layer designs, the rest use four layers or more, and 27% carry an open source license.
The most starred is SnackBus PSU by coriolisinstruments.
Microcontrollers on boards using the LM317_3PinPackage
What boards using the LM317_3PinPackage are built for
LM317_3PinPackage: common questions
Where can I find a LM317_3PinPackage reference design?
Each of the 11 boards on this page is a real design using the LM317_3PinPackage. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM317_3PinPackage ADJ pin?
The ADJ pin has a resistor to GND on 7 of 9 designs, most often 1 kΩ (then 220 Ω). Counted from the KiCad layouts of 9 open source designs using the LM317_3PinPackage.
What decoupling capacitors do designs use on the LM317_3PinPackage VI pin?
The VI pin has a decoupling capacitor on 4 of 9 designs, most often 220 µF (then 100 nF). Counted from the KiCad layouts of 9 open source designs using the LM317_3PinPackage.
Which microcontrollers do boards using the LM317_3PinPackage use?
Most are built on AVR/Arduino (2), PIC (1), Microchip SAM (1) and STM32 (1).
How big is a typical board using the LM317_3PinPackage?
The median is 99.2 × 80.2 mm, and 91% are two-layer designs.
What is the most popular open source board using the LM317_3PinPackage?
By GitHub stars, SnackBus PSU by coriolisinstruments, with 33 stars.
Can I simulate one of these boards using the LM317_3PinPackage before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.