6 open source boards using the LM317L_SO8
Real designs built with the LM317L_SO8, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Agc
thewonderidiot
158.8 × 121.9 mm190 parts4LMIT1A13 test project
servomouse
80 × 50 mm145 parts4LNo license1ESP32
EEG EMT 32
Raigetix
60 × 80 mm115 parts2LNo license0AVR/Arduino
SAM-ROBOT-CONTROLLER
dvmbnks
95.8 × 90.7 mm22 parts2LNo license0ESP32
Iprld
ICRS
100 × 100 mm88 parts2LNo license1Power V2 secondary
ICRS
48.5 × 99.8 mm18 parts2LNo license1
How designs wire the LM317L_SO8
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LM317L_SO8 connects to, and the resistors, capacitors and other passives placed on it.
- The ADJ pin has a pull-up to 5V on 5 of 5 designs, most often 240 Ω (then 500 Ω).
- The VI pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
- The VO pins have a decoupling capacitor on 4 of 5 designs, most often 1 µF (then 10 µF).
- The ADJ pin has a resistor to GND on 4 of 5 designs, most often 720 Ω (then 330 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VIpin 1 | Connected to: 12V 80% · a signal 20% |
|
| VOpin 2, 3, 6, 7 | Connected to: 5V 100% |
|
| ADJpin 4 | Connected to: Signal 100% |
|
| NCpin 5, 8 | Connected to: Not connected 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Iprld by ICRS, A13 test project by servomouse, Agc by thewonderidiot and SAM-ROBOT-CONTROLLER by dvmbnks.
The LM317L_SO8 in open source designs
The gallery holds 6 open source boards using the LM317L_SO8 from 5 GitHub repositories; a typical one measures about 87.9 × 95.2 mm and carries around 102 components.
67% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is Agc by thewonderidiot.
Microcontrollers on boards using the LM317L_SO8
What boards using the LM317L_SO8 are built for
LM317L_SO8: common questions
Where can I find a LM317L_SO8 reference design?
Each of the 6 boards on this page is a real design using the LM317L_SO8. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the LM317L_SO8 ADJ pin?
The ADJ pin has a pull-up to 5V on 5 of 5 designs, most often 240 Ω (then 500 Ω). Counted from the KiCad layouts of 5 open source designs using the LM317L_SO8.
What decoupling capacitors do designs use on the LM317L_SO8 VI pin?
The VI pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the LM317L_SO8.
What decoupling capacitors do designs use on the LM317L_SO8 VO pin?
The VO pins have a decoupling capacitor on 4 of 5 designs, most often 1 µF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the LM317L_SO8.
Which microcontrollers do boards using the LM317L_SO8 use?
Most are built on ESP32 (2) and AVR/Arduino (1).
How big is a typical board using the LM317L_SO8?
The median is 87.9 × 95.2 mm, and 67% are two-layer designs.
What is the most popular open source board using the LM317L_SO8?
By GitHub stars, Agc by thewonderidiot, with 1 stars.
Can I simulate one of these boards using the LM317L_SO8 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.