14 open source boards using the LM337
Real designs built with the LM337, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
PSU-5V-6V-Dual9V
ohdsp
100 × 100 mm103 parts2LTAPR-OHL-1.03Arithmetic
bodokaiser
49.5 × 48.8 mm59 parts2LNo license3Master segnale
dj-filippo241
100 × 220 mm275 parts4LNo license2Audio preamplifier power supply
flavian112
106.7 × 43.2 mm32 parts2LNo license1AVR/Arduino
Controller mb atu
c3h9dx
115 × 69.8 mm56 parts2LNo license0- schematic only · 697 parts
Master
plektra
697 parts2LCustom license0 - schematic only · 331 parts
Channel card
plektra
331 parts2LCustom license0 Mic
dj-filippo241
100 × 220 mm204 parts4LNo license2Fx ret
dj-filippo241
100 × 220 mm197 parts4LNo license2Canale
dj-filippo241
100 × 220 mm191 parts4LNo license2Master uscita-L
dj-filippo241
100 × 220 mm153 parts4LNo license2Master uscita-R
dj-filippo241
100 × 220 mm142 parts4LNo license2Mono
dj-filippo241
100 × 220 mm125 parts4LNo license2Fx send
dj-filippo241
100 × 220 mm118 parts4LNo license2
How designs wire the LM337
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LM337 connects to, and the resistors, capacitors and other passives placed on it.
- The ADJ pins have a resistor to GND on 5 of 5 designs, most often 2.2 kΩ (then 750 Ω).
- The ADJ pins have a capacitor to GND on 5 of 5 designs, most often 10 µF (then 100 nF).
- The VI pin has a capacitor to GND on 4 of 5 designs, most often 100 nF (then 1 µF).
- The ADJ pins have a series resistor on 3 of 5 designs, most often 120 Ω (then 240 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJpin 1, 4 | Connected to: Signal 86% |
|
| VIpin 2 | Connected to: TC7662Bx0A 43% |
|
| VOpin 3 | Connected to: Signal 60% · -12V 40% |
|
| NCpin 5, 8 | Connected to: Not connected 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Arithmetic by bodokaiser, PSU-5V-6V-Dual9V by ohdsp, Canale by dj-filippo241 and Audio preamplifier power supply by flavian112.
The LM337 in open source designs
The gallery holds 14 open source boards using the LM337 from 6 GitHub repositories; a typical one measures about 100 × 220 mm and carries around 148 components.
57% use four copper layers or more, and 7% carry an open source license.
The most starred is PSU-5V-6V-Dual9V by ohdsp.
Microcontrollers on boards using the LM337
What boards using the LM337 are built for
LM337: common questions
Where can I find a LM337 reference design?
Each of the 14 boards on this page is a real design using the LM337. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM337 ADJ pin?
The ADJ pins have a resistor to GND on 5 of 5 designs, most often 2.2 kΩ (then 750 Ω). Counted from the KiCad layouts of 5 open source designs using the LM337.
How is the LM337 VI pin connected?
The VI pin has a capacitor to GND on 4 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the LM337.
How is the LM337 VO pin connected?
The VO pin has a capacitor to GND on 3 of 5 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 5 open source designs using the LM337.
Which microcontrollers do boards using the LM337 use?
Most are built on AVR/Arduino (1).
How big is a typical board using the LM337?
The median is 100 × 220 mm, and 43% are two-layer designs.
What is the most popular open source board using the LM337?
By GitHub stars, PSU-5V-6V-Dual9V by ohdsp, with 3 stars.
Can I simulate one of these boards using the LM337 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.