5 open source boards using the LM358D
Real designs built with the LM358D, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Zx multisound
UzixLS
170 × 64 mm173 parts2LMIT37AVR/Arduino
TOBS
soldesign
87 × 87 mm100 parts2LGPL-3.03AVR/Arduino
Cremini blade atmega328p
nicklasfrahm
25 × 99 mm102 parts2LMIT1AVR/Arduino
ARDUINO-MEGA
Solomon-Menney
101.6 × 53.3 mm60 parts2LNo license0STM32
V2
Churrosoft
148.6 × 149.9 mm149 parts2LCERN-OHL-S-2.08
How designs wire the LM358D
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LM358D connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 5 of 5 designs.
- The - pins have a series resistor on 4 of 5 designs, most often 10 kΩ (then 24 kΩ).
- The + pins have a resistor to GND on 4 of 5 designs, most often 27 kΩ (then 20 kΩ).
- The + pins have a series resistor on 4 of 5 designs, most often 10 kΩ (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 40% · not connected 20% |
|
| -pin 2, 6 | Connected to: Signal 70% · not connected 20% |
|
| +pin 3, 5 | Connected to: Signal 80% |
|
| V-pin 4 | Connected to: GND 100% | — |
| Pin 7 | Connected to: Signal 80% · not connected 20% |
|
| V+pin 8 | Connected to: 5V 80% · a signal 20% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Zx multisound by UzixLS, V2 by Churrosoft, TOBS by soldesign and Cremini blade atmega328p by nicklasfrahm.
The LM358D in open source designs
The gallery holds 5 open source boards using the LM358D from 5 GitHub repositories; a typical one measures about 101.6 × 87 mm and carries around 102 components.
100% are two-layer designs, the rest use four layers or more, and 80% carry an open source license.
The most starred is Zx multisound by UzixLS.
Microcontrollers on boards using the LM358D
What boards using the LM358D are built for
LM358D: common questions
Where can I find a LM358D reference design?
Each of the 5 boards on this page is a real design using the LM358D. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM358D V- pin connected?
The V- pin is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the LM358D.
What resistor goes on the LM358D - pin?
The - pins have a series resistor on 4 of 5 designs, most often 10 kΩ (then 24 kΩ). Counted from the KiCad layouts of 5 open source designs using the LM358D.
What resistor goes on the LM358D + pin?
The + pins have a resistor to GND on 4 of 5 designs, most often 27 kΩ (then 20 kΩ). Counted from the KiCad layouts of 5 open source designs using the LM358D.
Which microcontrollers do boards using the LM358D use?
Most are built on AVR/Arduino (3) and STM32 (1).
How big is a typical board using the LM358D?
The median is 101.6 × 87 mm, and 100% are two-layer designs.
What is the most popular open source board using the LM358D?
By GitHub stars, Zx multisound by UzixLS, with 37 stars.
Can I simulate one of these boards using the LM358D before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.