10 open source boards using the LM358DR2G
Real designs built with the LM358DR2G, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
TechnicalDocs openUC2-HoloBox
openUC2
49 × 67 mm34 parts2LNo license5Fast response diode
amchagas
48.9 × 29.2 mm6 parts2LGPL-3.02ESP32
Lfp
maxakash
216 × 146 mm831 parts2LNo license0STM32
Panelised PD+Display
Sitengwu
143.5 × 70 mm144 parts2LNo license0Combined-II
sbv1307
174.9 × 67 mm83 parts2LNo license0Afe 230v 16a
kyuditsky
67.7 × 86.4 mm69 parts2LNo license0STM32
Retro Display Module
Sitengwu
70 × 100 mm121 parts2LNo license0- schematic only · 131 partsRaspberry Pi
Wanos board
gitwannes
131 parts2LCustom license1 PDB Board
thejamesrhodes
50 × 50 mm44 parts4LApache-2.01- schematic only · 63 parts
Wanos remote
gitwannes
63 parts2LCustom license1
How designs wire the LM358DR2G
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LM358DR2G connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 5 of 7 designs.
- The OUT_1 pin has a series resistor on 4 of 7 designs, most often 100 kΩ (then 1 kΩ).
- The + pins have a resistor to GND on 4 of 7 designs, most often 49.9 kΩ (then 20 kΩ).
- The - pins have a series resistor on 3 of 7 designs, most often 100 kΩ (then 1 MΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUT_1pin 1 | Connected to: A connector 43% |
|
| -pin 2, 6 | Connected to: A connector 31% · not connected 15% · GND 15% |
|
| +pin 3, 5 | Connected to: Signal 57% · GND 21% |
|
| V-pin 4 | Connected to: GND 71% | — |
| V+pin 8 | Connected to: 5V 60% · a signal 40% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include TechnicalDocs openUC2-HoloBox by openUC2, Fast response diode by amchagas, PDB Board by thejamesrhodes and Afe 230v 16a by kyuditsky.
The LM358DR2G in open source designs
The gallery holds 10 open source boards using the LM358DR2G from 8 GitHub repositories; a typical one measures about 68.8 × 68.5 mm and carries around 76 components.
90% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is TechnicalDocs openUC2-HoloBox by openUC2.
Microcontrollers on boards using the LM358DR2G
What boards using the LM358DR2G are built for
LM358DR2G: common questions
Where can I find a LM358DR2G reference design?
Each of the 10 boards on this page is a real design using the LM358DR2G. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM358DR2G V- pin connected?
The V- pin is tied to GND on 5 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the LM358DR2G.
What resistor goes on the LM358DR2G OUT_1 pin?
The OUT_1 pin has a series resistor on 4 of 7 designs, most often 100 kΩ (then 1 kΩ). Counted from the KiCad layouts of 7 open source designs using the LM358DR2G.
What resistor goes on the LM358DR2G + pin?
The + pins have a resistor to GND on 4 of 7 designs, most often 49.9 kΩ (then 20 kΩ). Counted from the KiCad layouts of 7 open source designs using the LM358DR2G.
Which microcontrollers do boards using the LM358DR2G use?
Most are built on STM32 (2), ESP32 (1) and Raspberry Pi (1).
How big is a typical board using the LM358DR2G?
The median is 68.8 × 68.5 mm, and 90% are two-layer designs.
What is the most popular open source board using the LM358DR2G?
By GitHub stars, TechnicalDocs openUC2-HoloBox by openUC2, with 5 stars.
Can I simulate one of these boards using the LM358DR2G before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.