9 open source boards using the LMR33630ADDAR
Real designs built with the LMR33630ADDAR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Esp32-led controller
arkandas
93.4 × 42.6 mm61 parts2LMIT5ESP32
Partial Drawer Controller v1
Robast-GmbH
408.7 × 50 mm556 parts4LMIT1STM32
OM-GOD
Sojoooo
403.7 × 202.9 mm475 parts4LNo license0FE UFPR 4 0
josearistidesbail
159.6 × 130 mm313 parts4LNo license0FilMachine Mainboard
yesnoj
110 × 90 mm198 parts4LNo license012V-5V 2A-Synchronous-Buck-Converter
abboju-nikhil
56.6 × 40 mm31 parts2LNo license0ESP32
Partial Drawer Controller v1 hotfix
Robast-GmbH
408.7 × 50 mm556 parts4LMIT1ESP32
Drawer Controller v4
Robast-GmbH
118 × 47 mm126 parts4LMIT1ESP32
Drawer Controller v4 hotfix
Robast-GmbH
118 × 47 mm126 parts4LMIT1
How designs wire the LMR33630ADDAR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LMR33630ADDAR connects to, and the resistors, capacitors and other passives placed on it.
- The FB pin has a resistor to GND on 6 of 6 designs, most often 24.9 kΩ (then 330 kΩ).
- The VCC pin has a capacitor to GND on 6 of 6 designs, most often 1 µF.
- The BOOT pin has a series capacitor on 6 of 6 designs, most often 100 nF.
- The SW pin has a series capacitor on 6 of 6 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PGNDpin 1 | Connected to: GND 100% | — |
| VINpin 2 | Connected to: VIN 100% |
|
| ENpin 3 | Connected to: VIN 83% · a signal 17% | — |
| PGpin 4 | Connected to: Not connected 50% · a signal 50% |
|
| FBpin 5 | Connected to: Signal 100% |
|
| VCCpin 6 | Connected to: Signal 83% · VCC 17% |
|
| BOOTpin 7 | Connected to: Signal 100% |
|
| SWpin 8 | Connected to: Signal 100% |
|
| EPpin 9 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Esp32-led controller by arkandas, Drawer Controller v4 by Robast-GmbH, 12V-5V 2A-Synchronous-Buck-Converter by abboju-nikhil and FE UFPR 4 0 by josearistidesbail.
The LMR33630ADDAR in open source designs
The gallery holds 9 open source boards using the LMR33630ADDAR from 6 GitHub repositories; a typical one measures about 118 × 50 mm and carries around 198 components.
78% use four copper layers or more, and 56% carry an open source license.
The most starred is Esp32-led controller by arkandas.
Parts used alongside the LMR33630ADDAR
What boards using the LMR33630ADDAR are built for
LMR33630ADDAR: common questions
Where can I find a LMR33630ADDAR reference design?
Each of the 9 boards on this page is a real design using the LMR33630ADDAR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LMR33630ADDAR FB pin?
The FB pin has a resistor to GND on 6 of 6 designs, most often 24.9 kΩ (then 330 kΩ). Counted from the KiCad layouts of 6 open source designs using the LMR33630ADDAR.
How is the LMR33630ADDAR VCC pin connected?
The VCC pin has a capacitor to GND on 6 of 6 designs, most often 1 µF. Counted from the KiCad layouts of 6 open source designs using the LMR33630ADDAR.
How is the LMR33630ADDAR BOOT pin connected?
The BOOT pin has a series capacitor on 6 of 6 designs, most often 100 nF. Counted from the KiCad layouts of 6 open source designs using the LMR33630ADDAR.
What parts are used alongside the LMR33630ADDAR?
The AMS1117-3.3, SN65HVD230DR and UCC27524DR appear in the most repositories here.
Which microcontrollers do boards using the LMR33630ADDAR use?
Most are built on ESP32 (5) and STM32 (1).
How big is a typical board using the LMR33630ADDAR?
The median is 118 × 50 mm, and 22% are two-layer designs.
What is the most popular open source board using the LMR33630ADDAR?
By GitHub stars, Esp32-led controller by arkandas, with 5 stars.
Can I simulate one of these boards using the LMR33630ADDAR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.