5 open source boards using the LMR50410

Real designs built with the LMR50410, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the LMR50410

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LMR50410 connects to, and the resistors, capacitors and other passives placed on it.

  • The CB pin has a series capacitor on 5 of 5 designs, most often 100 nF.
  • The FB pin has a resistor to GND on 5 of 5 designs, most often 22.1 kΩ (then 22 kΩ).
  • The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 2.2 µF (then 100 nF).
  • The SW pin has a series capacitor on 5 of 5 designs, most often 100 nF.
CBpin 1Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (5)
GNDpin 2Connected to: GND 100%
FBpin 3Connected to: Signal 100%
  • Resistor to GND on 100% · 22.1 kΩ (2), 22 kΩ (1), 2.7 kΩ (1)
  • Series resistor on 60% · 88.7 kΩ (2), 51 kΩ (1)
  • Pull-up to 3.3V on 40% · 6.2 kΩ (1), 115 kΩ (1)
SHDNpin 4Connected to: Signal 60% · 12V 40%
  • Capacitor to GND on 80% · 100 nF (3), 2.2 µF (2), 47 µF (1)
VINpin 5Connected to: 12V 60% · a signal 40%
  • Decoupling capacitor on 100% · 2.2 µF (4), 100 nF (3), 47 µF (1)
SWpin 6Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (5)
  • Inductor on 100% · 15 µH (2), 4.7 µH (2), 33 µH (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PA Power V1 by M0LTE, CAN motor controller by wjklimek1, Orc by aramder and Lamp-2 by DodoZimmermann.

The LMR50410 in open source designs

The gallery holds 5 open source boards using the LMR50410 from 5 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 111 components.

60% use four copper layers or more, and 40% carry an open source license.

The most starred is PA Power V1 by M0LTE.

Microcontrollers on boards using the LMR50410

LMR50410: common questions

Where can I find a LMR50410 reference design?

Each of the 5 boards on this page is a real design using the LMR50410. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LMR50410 CB pin connected?

The CB pin has a series capacitor on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the LMR50410.

What resistor goes on the LMR50410 FB pin?

The FB pin has a resistor to GND on 5 of 5 designs, most often 22.1 kΩ (then 22 kΩ). Counted from the KiCad layouts of 5 open source designs using the LMR50410.

What decoupling capacitors do designs use on the LMR50410 VIN pin?

The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 2.2 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the LMR50410.

What parts are used alongside the LMR50410?

The ACS770xCB-050B-PFF, ADS1015IDGS, AP2204K-ADJ, LMR38020 and MCP4725A0T appear in the most repositories here.

Which microcontrollers do boards using the LMR50410 use?

Most are built on ESP32 (2) and STM32 (1).

How big is a typical board using the LMR50410?

The median is 100 × 100 mm, and 40% are two-layer designs.

What is the most popular open source board using the LMR50410?

By GitHub stars, PA Power V1 by M0LTE, with 15 stars.

Can I simulate one of these boards using the LMR50410 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part