30 open source boards using the ADS1015IDGS
Real designs built with the ADS1015IDGS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
HF PA Radio Interface
M0LTE
100 × 100 mm180 parts2LNo license15Raspberry Pi
Pinbot electronics
Pinbot-factory
114 × 65 mm204 parts4LCERN-OHL-S-2.05Solar panel side-Z
proveskit
100 × 100 mm41 parts4LCERN-OHL-W-2.04Gripper hat
nhnifong
65 × 30 mm52 parts4LNo license3ESP32
Reliable-Temp-Monitor
Alex-C-EE
66.9 × 66.9 mm112 parts4LNo license1ESP32
Helix vape
stevensun369
30 × 97 mm77 parts2LNo license1Chibi-T Furoshiki AutoAirAdjust
todateman
50 × 50 mm30 parts2LMIT1- schematic only · 38 parts
Epicura spec
manasXP
38 partsNo license1 RP2040/RP2350
2023-24 Power Supply 1
cdagher
275 × 270 mm320 parts4LMIT0ESP32
Microbot v1.1
Freimor
185 × 58.6 mm190 parts4LNo license0RP2040/RP2350
HF PA Radio Interface
RADARC
100 × 100 mm180 parts2LNo license0AA PwrSens Dist
AESilky
147.3 × 154.4 mm135 parts2LNo license0ESP32
Multipurpose ESP32 Gamepad
pacman314159
136 × 95 mm131 parts4LNo license0Power8Board
Harry-IV
102 × 102 mm107 parts6LGPL-3.00DCI
sebaherrera74
87 × 63 mm32 parts2LNo license0Printhead
Fiberprinter
35 × 35 mm63 parts2LNo license4XY Faces V3r
proveskit
83 × 98 mm33 parts4LCERN-OHL-W-2.04RP2040/RP2350
2023-24 Power Supply 2
cdagher
325 × 270 mm320 parts4LMIT0PA Power V1
RADARC
100 × 100 mm111 parts4LNo license0Band Switch board 2026 small
satspares
90 × 45 mm31 parts2LMIT0PA Power V1
M0LTE
100 × 100 mm111 parts4LNo license15XY Faces V3lp
proveskit
83 × 98 mm27 parts4LCERN-OHL-W-2.042023-24 Power Supply
cdagher
325 × 235 mm265 parts2LMIT0ESP32
Control board
Freimor
90 × 110 mm105 parts4LNo license0XY Face V4
proveskit
83 × 98 mm25 parts4LCERN-OHL-W-2.04ESP32
Control board(2024-10-31 160845)
Freimor
90 × 110 mm105 parts4LNo license0Z Face V3
proveskit
100 × 100 mm21 parts4LCERN-OHL-W-2.042U XY V1a
proveskit
83 × 212.6 mm19 parts4LCERN-OHL-W-2.04XY Face V4nb
proveskit
83 × 98 mm19 parts4LCERN-OHL-W-2.04XY V3 Stencil
proveskit
83 × 98 mm9 parts4LCERN-OHL-W-2.04
How designs wire the ADS1015IDGS
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the ADS1015IDGS connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 13 of 16 designs, most often 100 nF (then 4.7 µF).
- The ADDR pin is tied to GND on 11 of 16 designs (a signal on 4).
- The SDA pin has a pull-up to 3.3V on 9 of 15 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL pin has a pull-up to 3.3V on 9 of 15 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADDRpin 1 | Connected to: GND 69% · a signal 25% | — |
| GNDpin 3 | Connected to: GND 94% | — |
| AIN0pin 4 | Connected to: A connector 50% |
|
| AIN1pin 5 | Connected to: A connector 56% |
|
| AIN2pin 6 | Connected to: A connector 44% |
|
| AIN3pin 7 | Connected to: A connector 38% |
|
| VDDpin 8 | Connected to: 3.3V 75% · a signal 19% |
|
| SDApin 9 | Connected to: A connector 47%, the microcontroller 40% |
|
| SCLpin 10 | Connected to: A connector 47%, the microcontroller 40% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include HF PA Radio Interface by M0LTE, Pinbot electronics by Pinbot-factory, Printhead pcb by Fiberprinter and 2U XY V1a by proveskit.
The ADS1015IDGS in open source designs
The gallery holds 30 open source boards using the ADS1015IDGS from 17 GitHub repositories; a typical one measures about 90 × 98 mm and carries around 91 components.
69% use four copper layers or more, and 50% carry an open source license.
The most starred is HF PA Radio Interface by M0LTE.
Parts used alongside the ADS1015IDGS
Microcontrollers on boards using the ADS1015IDGS
What boards using the ADS1015IDGS are built for
ADS1015IDGS: common questions
Where can I find a ADS1015IDGS reference design?
Each of the 30 boards on this page is a real design using the ADS1015IDGS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the ADS1015IDGS VDD pin?
The VDD pin has a decoupling capacitor on 13 of 16 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 16 open source designs using the ADS1015IDGS.
How is the ADS1015IDGS ADDR pin connected?
The ADDR pin is tied to GND on 11 of 16 designs (a signal on 4). Counted from the KiCad layouts of 16 open source designs using the ADS1015IDGS.
What pull-up resistor is used on the ADS1015IDGS SDA pin?
The SDA pin has a pull-up to 3.3V on 9 of 15 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 16 open source designs using the ADS1015IDGS.
What parts are used alongside the ADS1015IDGS?
The USBLC6-2SC6, 24LC32, 74AHCT125, 74LVC1G17 and 74LVC74 appear in the most repositories here.
Which microcontrollers do boards using the ADS1015IDGS use?
Most are built on ESP32 (6), RP2040/RP2350 (4) and Raspberry Pi (1).
How big is a typical board using the ADS1015IDGS?
The median is 90 × 98 mm, and 31% are two-layer designs.
What is the most popular open source board using the ADS1015IDGS?
By GitHub stars, HF PA Radio Interface by M0LTE, with 15 stars.
Can I simulate one of these boards using the ADS1015IDGS before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.