9 open source boards using the LS74
Real designs built with the LS74, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Olivetti M20 L1 schematics
anchorz
457.1 × 308 mm410 parts4LMIT4TA8-FDC
felge1966
160 × 100.3 mm60 parts2LGPL-3.03Taito video processor
nmikstas
304.8 × 279.4 mm346 parts2LNo license0- schematic only · 24 parts
Z80proto
yasunoxx
24 partsMIT0 AVR/Arduino
Q10MF BOARD
brijohn
281 × 79 mm44 parts2LNo license9AVR/Arduino
QX10 Titan QXPC Memory Board
brijohn
254 × 63.5 mm40 parts2LNo license9Qx10 sound card
brijohn
281 × 79 mm32 parts2LNo license9Trigger
homebrew8088
25.4 × 21 mm6 parts2LGPL-3.027QX-10 1MB Memory Expansion Board
brijohn
281 × 79 mm22 parts2LNo license9
How designs wire the LS74
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LS74 connects to, and the resistors, capacitors and other passives placed on it.
- The A5 pin is tied to GND on 3 of 5 designs (a signal on 2).
- The A1 pin has a pull-up to 5P on 2 of 5 designs, most often 3.3 kΩ.
- The DQ1 pin has a capacitor to GND on 2 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A5pin 7 | Connected to: GND 60% · a signal 40% | — |
| A1pin 11 | Connected to: Signal 80% · not connected 20% |
|
| DQ1pin 14 | Connected to: 74LS04 40% · 5P 40% |
|
21 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Trigger by homebrew8088, QX-10 1MB Memory Expansion Board by brijohn, Olivetti M20 L1 schematics by anchorz and TA8-FDC by felge1966.
The LS74 in open source designs
The gallery holds 9 open source boards using the LS74 from 6 GitHub repositories; a typical one measures about 281 × 79 mm and carries around 40 components.
88% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Trigger by homebrew8088.
Microcontrollers on boards using the LS74
What boards using the LS74 are built for
LS74: common questions
Where can I find a LS74 reference design?
Each of the 9 boards on this page is a real design using the LS74. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LS74 A5 pin connected?
The A5 pin is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the LS74.
What pull-up resistor is used on the LS74 A1 pin?
The A1 pin has a pull-up to 5P on 2 of 5 designs, most often 3.3 kΩ. Counted from the KiCad layouts of 5 open source designs using the LS74.
How is the LS74 DQ1 pin connected?
The DQ1 pin has a capacitor to GND on 2 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the LS74.
What parts are used alongside the LS74?
The 74LS04, LS14, LS32, 74LS245 and LS00 appear in the most repositories here.
Which microcontrollers do boards using the LS74 use?
Most are built on AVR/Arduino (2).
How big is a typical board using the LS74?
The median is 281 × 79 mm, and 88% are two-layer designs.
What is the most popular open source board using the LS74?
By GitHub stars, Trigger by homebrew8088, with 27 stars.
Can I simulate one of these boards using the LS74 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.