5 open source boards using the LTC4411

Real designs built with the LTC4411, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the LTC4411

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the LTC4411 connects to, and the resistors, capacitors and other passives placed on it.

  • The OUT pin has a capacitor to GND on 4 of 5 designs, most often 4.7 µF (then 100 nF).
  • The IN pin has a series resistor on 3 of 5 designs, most often 10 kΩ (then 4.75 kΩ).
  • The STAT pin is left unconnected on 3 of 5 designs.
  • The IN pin has a capacitor to GND on 2 of 5 designs, most often 47 µF (then 10 µF).
INpin 1Connected to: Signal 60% · BATT 40%
  • Series resistor on 60% · 10 kΩ (1), 4.75 kΩ (1), 261 Ω (1)
  • Capacitor to GND on 40% · 47 µF (1), 10 µF (1)
GNDpin 2Connected to: GND 80% · a signal 20%
CTLpin 3Connected to: Signal 60% · not connected 20% · GND 20%
  • Series resistor on 40% · 10 kΩ (1), 1 kΩ (1), 1 MΩ (1)
STATpin 4Connected to: Not connected 60% · GND 20% · a signal 20%
OUTpin 5Connected to: Signal 60% · 5V 40%
  • Capacitor to GND on 80% · 4.7 µF (3), 100 nF (1), 1 µF (1)
  • Series resistor on 40% · 51 mΩ (2), 100 Ω (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Fox-1-MPPT by FaradayRF, Draco by xdandys, Prototipo 1 : Base LPCXpresso1769 - VOP24 by brengi and ProjectFreeCad by ananevego.

The LTC4411 in open source designs

The gallery holds 5 open source boards using the LTC4411 from 5 GitHub repositories; a typical one measures about 90.8 × 62 mm and carries around 122 components.

60% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.

The most starred is Fox-1-MPPT by FaradayRF.

Microcontrollers on boards using the LTC4411

LTC4411: common questions

Where can I find a LTC4411 reference design?

Each of the 5 boards on this page is a real design using the LTC4411. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LTC4411 OUT pin connected?

The OUT pin has a capacitor to GND on 4 of 5 designs, most often 4.7 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the LTC4411.

What resistor goes on the LTC4411 IN pin?

The IN pin has a series resistor on 3 of 5 designs, most often 10 kΩ (then 4.75 kΩ). Counted from the KiCad layouts of 5 open source designs using the LTC4411.

How is the LTC4411 STAT pin connected?

The STAT pin is left unconnected on 3 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the LTC4411.

Which microcontrollers do boards using the LTC4411 use?

Most are built on ESP32 (1), PIC (1) and STM32 (1).

How big is a typical board using the LTC4411?

The median is 90.8 × 62 mm, and 60% are two-layer designs.

What is the most popular open source board using the LTC4411?

By GitHub stars, Fox-1-MPPT by FaradayRF, with 62 stars.

Can I simulate one of these boards using the LTC4411 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part