9 open source boards using the MCP6001R
Real designs built with the MCP6001R, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Iot wifi uno hw
iotmakervn
68.5 × 53.3 mm48 parts2LNo license26RP2040/RP2350
Pico H-bridge complete
rosstimo
84.1 × 66 mm77 parts4LCC-BY-NC-4.01RP2040/RP2350
Stencil
Bergi84
259.1 × 177.8 mm156 parts4LNo license0AVR/Arduino
Leviosa
Kay-Jack
80 × 80 mm47 parts2LNo license0Precision-Light-Sensor-AFE
shyver
25 × 10 mm8 parts2LMIT0RP2040/RP2350
PumpCon
Bergi84
50 × 50 mm134 parts4LNo license0RP2040/RP2350
HydCircCon
Bergi84
50 × 40 mm111 parts4LNo license0RP2040/RP2350
SensorNode
Bergi84
35.5 × 35 mm111 parts4LNo license0RP2040/RP2350
ReservoirCon
Bergi84
30 × 30 mm66 parts4LNo license0
How designs wire the MCP6001R
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MCP6001R connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 5 of 5 designs.
- Pin 1 has a series resistor on 3 of 5 designs, most often 10 kΩ (then 8.2 Ω).
- The - pin has a series resistor on 3 of 5 designs, most often 10 kΩ (then 8.2 Ω).
- The V+ pin has a decoupling capacitor on 2 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 40% |
|
| V+pin 2 | Connected to: 3.3V 100% |
|
| +pin 3 | Connected to: Signal 80% · GND 20% |
|
| -pin 4 | Connected to: Signal 80% · 3.3V 20% |
|
| V-pin 5 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Iot wifi uno hw by iotmakervn, Pico H-bridge complete by rosstimo, HydCircCon by Bergi84 and Leviosa by Kay-Jack.
The MCP6001R in open source designs
The gallery holds 9 open source boards using the MCP6001R from 5 GitHub repositories; a typical one measures about 50 × 50 mm and carries around 77 components.
67% use four copper layers or more, and 11% carry an open source license.
The most starred is Iot wifi uno hw by iotmakervn.
Microcontrollers on boards using the MCP6001R
What boards using the MCP6001R are built for
MCP6001R: common questions
Where can I find a MCP6001R reference design?
Each of the 9 boards on this page is a real design using the MCP6001R. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP6001R V- pin connected?
The V- pin is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MCP6001R.
What resistor goes on the MCP6001R pin 1?
Pin 1 has a series resistor on 3 of 5 designs, most often 10 kΩ (then 8.2 Ω). Counted from the KiCad layouts of 5 open source designs using the MCP6001R.
What resistor goes on the MCP6001R - pin?
The - pin has a series resistor on 3 of 5 designs, most often 10 kΩ (then 8.2 Ω). Counted from the KiCad layouts of 5 open source designs using the MCP6001R.
Which microcontrollers do boards using the MCP6001R use?
Most are built on RP2040/RP2350 (6), AVR/Arduino (1) and ESP8266 (1).
How big is a typical board using the MCP6001R?
The median is 50 × 50 mm, and 33% are two-layer designs.
What is the most popular open source board using the MCP6001R?
By GitHub stars, Iot wifi uno hw by iotmakervn, with 26 stars.
Can I simulate one of these boards using the MCP6001R before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.