7 open source boards using the MMC5603NJ
Real designs built with the MMC5603NJ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Fmc usb gpio spi jtag
chipsalliance
76.5 × 69 mm136 parts6LApache-2.019STM32
Wand
ayuusweetfish
63.2 × 23.9 mm65 parts2LCERN-OHL-S-2.01ESP32
Kabot
kabot-io
89 × 92.5 mm137 parts2LCC-BY-NC-4.00Minicontrol
Jotrorox
50 × 36 mm58 parts4LBSD-2-Clause0Lab3
Felix-Jr056
26.5 × 14.5 mm12 parts2LNo license0MMC5603-Module
HackableElectronics
12.5 × 21.1 mm7 parts2LLGPL-2.10STM32
Pendu
ayuusweetfish
36 × 20 mm26 parts2LCERN-OHL-S-2.01
How designs wire the MMC5603NJ
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the MMC5603NJ connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 2.2 µF).
- The VSA pin is tied to GND on 6 of 6 designs.
- The SCL pin has a pull-up to 3.3V on 4 of 6 designs, most often 2.7 kΩ (then 2.2 kΩ).
- The SDA pin has a pull-up to 3.3V on 4 of 6 designs, most often 2.7 kΩ (then 2.2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSApin A1 | Connected to: GND 100% | — |
| SCLpin A2 | Connected to: A connector 67% |
|
| VDDpin B1 | Connected to: 3.3V 83% · a signal 17% |
|
| SDApin B2 | Connected to: A connector 67% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Fmc usb gpio spi jtag by chipsalliance, Pendu by ayuusweetfish, Lab3 by Felix-Jr056 and MMC5603-Module by HackableElectronics.
The MMC5603NJ in open source designs
The gallery holds 7 open source boards using the MMC5603NJ from 6 GitHub repositories; a typical one measures about 50 × 23.9 mm and carries around 58 components.
71% are two-layer designs, the rest use four layers or more, and 71% carry an open source license.
The most starred is Fmc usb gpio spi jtag by chipsalliance.
What boards using the MMC5603NJ are built for
MMC5603NJ: common questions
Where can I find a MMC5603NJ reference design?
Each of the 7 boards on this page is a real design using the MMC5603NJ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MMC5603NJ VDD pin?
The VDD pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 6 open source designs using the MMC5603NJ.
How is the MMC5603NJ VSA pin connected?
The VSA pin is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the MMC5603NJ.
What pull-up resistor is used on the MMC5603NJ SCL pin?
The SCL pin has a pull-up to 3.3V on 4 of 6 designs, most often 2.7 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 6 open source designs using the MMC5603NJ.
Which microcontrollers do boards using the MMC5603NJ use?
Most are built on STM32 (2) and ESP32 (1).
How big is a typical board using the MMC5603NJ?
The median is 50 × 23.9 mm, and 71% are two-layer designs.
What is the most popular open source board using the MMC5603NJ?
By GitHub stars, Fmc usb gpio spi jtag by chipsalliance, with 19 stars.
Can I simulate one of these boards using the MMC5603NJ before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.