6 open source boards using the MT6701
Real designs built with the MT6701, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
SiPDrive
Just4Stan
20 × 27 mm89 parts6LCC-BY-NC-4.04ESP32
Haptic knob
wirano
50 × 50 mm66 parts4LNo license3STM32
Vfo controller
xflyingcat
56 × 50 mm53 parts2LMIT1RP2040/RP2350
Servodrive — board S, single board
sequoia-hope
65 × 65 mm190 parts6LNo license0RP2040/RP2350
Servodrive — board A, motor board
sequoia-hope
65 × 65 mm132 parts6LNo license0Rp2040 encoder
Twisted-Fields
36.7 × 33.3 mm10 parts2LCustom license419
How designs wire the MT6701
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MT6701 connects to, and the resistors, capacitors and other passives placed on it.
- The PUSH pin is left unconnected on 5 of 5 designs.
- The NC pins have a capacitor to GND on 2 of 5 designs, most often 100 nF (then 1 µF).
- The A/DO/SDA pin has a series resistor on 2 of 5 designs, most often 100 Ω.
- The B/CLK/SCL pin has a series resistor on 2 of 5 designs, most often 100 Ω.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 1, 2, 3, 4, 10 | Connected to: Not connected 55% · 3.3V 23% |
|
| PUSHpin 5 | Connected to: Not connected 100% | — |
| A/DO/SDApin 6 | Connected to: The microcontroller 60% |
|
| B/CLK/SCLpin 7 | Connected to: The microcontroller 60% |
|
| Wpin 9 | Connected to: Not connected 100% | — |
| Upin 11 | Connected to: Not connected 100% | — |
| Vpin 12 | Connected to: Not connected 100% | — |
| VDDpin 13 | Connected to: 3.3V 100% |
|
| OUTpin 15 | Connected to: Not connected 100% | — |
| GNDpin 16 | Connected to: GND 100% | — |
| EPpin 17 | Connected to: GND 100% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Rp2040 encoder by Twisted-Fields, SiPDrive by Just4Stan, Haptic knob by wirano and Vfo controller by xflyingcat.
The MT6701 in open source designs
The gallery holds 6 open source boards using the MT6701 from 5 GitHub repositories; a typical one measures about 53 × 50 mm and carries around 78 components.
67% use four copper layers or more, and 17% carry an open source license.
The most starred is Rp2040 encoder by Twisted-Fields.
Microcontrollers on boards using the MT6701
What boards using the MT6701 are built for
MT6701: common questions
Where can I find a MT6701 reference design?
Each of the 6 boards on this page is a real design using the MT6701. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MT6701 PUSH pin connected?
The PUSH pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MT6701.
How is the MT6701 NC pin connected?
The NC pins have a capacitor to GND on 2 of 5 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the MT6701.
What resistor goes on the MT6701 A/DO/SDA pin?
The A/DO/SDA pin has a series resistor on 2 of 5 designs, most often 100 Ω. Counted from the KiCad layouts of 5 open source designs using the MT6701.
Which microcontrollers do boards using the MT6701 use?
Most are built on RP2040/RP2350 (2), ESP32 (1) and STM32 (1).
How big is a typical board using the MT6701?
The median is 53 × 50 mm, and 33% are two-layer designs.
What is the most popular open source board using the MT6701?
By GitHub stars, Rp2040 encoder by Twisted-Fields, with 419 stars.
Can I simulate one of these boards using the MT6701 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.