10 open source boards using the NJM4558
Real designs built with the NJM4558, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
TR-808 clone
mkomakonkon
442 × 421.7 mm1268 parts2LNo license5Ts9 clone
ioankatsi
100 × 80 mm28 parts2LNo license4ESP32
ESP32
Tomoshibi-technology
150 × 150 mm224 parts2LMIT0MPXDecorder-V2
akira345
100 × 84.2 mm119 parts2LNo license0Toaru jisaku no-Railgun
Yu-hotspring
100 × 54.6 mm78 parts2LNo license0DistortionPedal
Outdatedcandy92
50.4 × 48.4 mm56 parts2LNo license0Distortion-Pedal
Outdatedcandy92
45 × 60 mm53 parts4LCERN-OHL-W-2.00Bmp2
bubbajfett
58 × 46.4 mm52 parts2LCC0-1.014OperationalFuzz
kanengomibako
43 × 47 mm32 parts2LUnlicense11Ecstacy
bubbajfett
59.3 × 36.8 mm41 parts2LCC0-1.014
How designs wire the NJM4558
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the NJM4558 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 7 has a series resistor on 8 of 9 designs, most often 470 kΩ (then 2.2 kΩ).
- Pin 1 has a series resistor on 7 of 9 designs, most often 4.7 kΩ (then 100 kΩ).
- The - pins have a series resistor on 7 of 9 designs, most often 4.7 kΩ (then 100 kΩ).
- The V- pin is tied to GND on 8 of 9 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 78% · not connected 22% |
|
| -pin 2, 6 | Connected to: Signal 83% |
|
| +pin 3, 5 | Connected to: Signal 72% · GND 17% |
|
| V-pin 4 | Connected to: GND 89% | — |
| Pin 7 | Connected to: Signal 89% |
|
| V+pin 8 | Connected to: VCC 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bmp2 by bubbajfett, OperationalFuzz by kanengomibako, TR-808 clone by mkomakonkon and Ts9 clone by ioankatsi.
The NJM4558 in open source designs
The gallery holds 10 open source boards using the NJM4558 from 9 GitHub repositories; a typical one measures about 79.6 × 57.3 mm and carries around 55 components.
90% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Bmp2 by bubbajfett.
Parts used alongside the NJM4558
Microcontrollers on boards using the NJM4558
What boards using the NJM4558 are built for
NJM4558: common questions
Where can I find a NJM4558 reference design?
Each of the 10 boards on this page is a real design using the NJM4558. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the NJM4558 pin 7?
Pin 7 has a series resistor on 8 of 9 designs, most often 470 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 9 open source designs using the NJM4558.
What resistor goes on the NJM4558 pin 1?
Pin 1 has a series resistor on 7 of 9 designs, most often 4.7 kΩ (then 100 kΩ). Counted from the KiCad layouts of 9 open source designs using the NJM4558.
What resistor goes on the NJM4558 - pin?
The - pins have a series resistor on 7 of 9 designs, most often 4.7 kΩ (then 100 kΩ). Counted from the KiCad layouts of 9 open source designs using the NJM4558.
Which microcontrollers do boards using the NJM4558 use?
Most are built on ESP32 (2).
How big is a typical board using the NJM4558?
The median is 79.6 × 57.3 mm, and 90% are two-layer designs.
What is the most popular open source board using the NJM4558?
By GitHub stars, Bmp2 by bubbajfett, with 14 stars.
Can I simulate one of these boards using the NJM4558 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.