6 open source boards using the OP275
Real designs built with the OP275, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
VCO
nickajeglin
37 × 113.9 mm104 parts2LNo license208MFOSmod
Micosilent
50 × 100 mm102 parts2LCC-BY-NC-4.013VCO
VincentPeters
37 × 113.9 mm104 parts2LNo license9TI MSP430/CC
Huracan MkIII PreAmp Board
terjeio
175 × 86 mm175 parts2LNo license2STM32
Stm audio board v3 dsp board
Papproni
265 × 117 mm391 parts4LMIT1VCO
gehel
46 × 113 mm94 parts4LNo license0
How designs wire the OP275
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the OP275 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series capacitor on 5 of 6 designs, most often 100 pF.
- Pin 1 has a series resistor on 5 of 6 designs, most often 2 kΩ (then 1 kΩ).
- The - pins have a series capacitor on 5 of 6 designs, most often 100 pF.
- The - pins have a series resistor on 5 of 6 designs, most often 100 kΩ (then 1 MΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| -pin 2, 6 | Connected to: Signal 100% |
|
| +pin 3, 5 | Connected to: GND 67% · a signal 33% |
|
| V-pin 4 | Connected to: -12V 100% |
|
| Pin 7 | Connected to: Signal 100% |
|
| V+pin 8 | Connected to: 12V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include VCO by nickajeglin, MFOSmod by Micosilent, VCO by VincentPeters and Huracan MkIII PreAmp Board by terjeio.
The OP275 in open source designs
The gallery holds 6 open source boards using the OP275 from 6 GitHub repositories; a typical one measures about 48 × 113.5 mm and carries around 104 components.
67% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is VCO by nickajeglin.
Microcontrollers on boards using the OP275
What boards using the OP275 are built for
OP275: common questions
Where can I find a OP275 reference design?
Each of the 6 boards on this page is a real design using the OP275. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the OP275 pin 1 connected?
Pin 1 has a series capacitor on 5 of 6 designs, most often 100 pF. Counted from the KiCad layouts of 6 open source designs using the OP275.
How is the OP275 - pin connected?
The - pins have a series capacitor on 5 of 6 designs, most often 100 pF. Counted from the KiCad layouts of 6 open source designs using the OP275.
How is the OP275 pin 7 connected?
Pin 7 has a series capacitor on 5 of 6 designs, most often 100 pF. Counted from the KiCad layouts of 6 open source designs using the OP275.
What parts are used alongside the OP275?
The LM13700, TL071, TL072, TL074 and SSM2212 appear in the most repositories here.
Which microcontrollers do boards using the OP275 use?
Most are built on STM32 (1) and TI MSP430/CC (1).
How big is a typical board using the OP275?
The median is 48 × 113.5 mm, and 67% are two-layer designs.
What is the most popular open source board using the OP275?
By GitHub stars, VCO by nickajeglin, with 208 stars.
Can I simulate one of these boards using the OP275 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.