10 open source boards using the OPA1656IDR

Real designs built with the OPA1656IDR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

10 boardsClear filters|Most starred

How designs wire the OPA1656IDR

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the OPA1656IDR connects to, and the resistors, capacitors and other passives placed on it.

  • The OUT pins have a series resistor on 7 of 7 designs, most often 20 kΩ (then 10 kΩ).
  • The -_2 pin has a series resistor on 6 of 7 designs, most often 20 kΩ (then 100 kΩ).
  • The -_6 pin has a series resistor on 6 of 7 designs, most often 20 kΩ (then 10 Ω).
  • The +_3 pin has a series resistor on 3 of 7 designs, most often 0 Ω (then 100 Ω).
OUTpin 1, 7Connected to: Signal 93%
  • Series resistor on 100% · 20 kΩ (8), 10 kΩ (3), 10 Ω (2)
-_2pin 2Connected to: Signal 100%
  • Series resistor on 86% · 20 kΩ (4), 100 kΩ (2), 10 Ω (1)
+_3pin 3Connected to: Signal 71%
  • Series resistor on 43% · 0 Ω (2), 100 Ω (2)
  • Capacitor to GND on 43% · 1 µF (1)
  • Resistor to GND on 43% · 47.5 kΩ (1), 10 kΩ (1)
V-_4pin 4Connected to: -12V 71%
-_6pin 6Connected to: Signal 86%
  • Series resistor on 86% · 20 kΩ (4), 10 Ω (1), 19.1 kΩ (1)
V+_8pin 8Connected to: 12V 86%

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pandore by filliformes, Phono adc eval by birdybro, GAS Rev A - Ext Tank Routing by jdg511 and PANEL CARDS by k16shikano.

The OPA1656IDR in open source designs

The gallery holds 10 open source boards using the OPA1656IDR from 7 GitHub repositories; a typical one measures about 165 × 105 mm and carries around 177 components.

70% use four copper layers or more, and 10% carry an open source license.

The most starred is Pandore by filliformes.

Parts used alongside the OPA1656IDR

Microcontrollers on boards using the OPA1656IDR

What boards using the OPA1656IDR are built for

OPA1656IDR: common questions

Where can I find a OPA1656IDR reference design?

Each of the 10 boards on this page is a real design using the OPA1656IDR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the OPA1656IDR OUT pin?

The OUT pins have a series resistor on 7 of 7 designs, most often 20 kΩ (then 10 kΩ). Counted from the KiCad layouts of 7 open source designs using the OPA1656IDR.

What resistor goes on the OPA1656IDR -_2 pin?

The -_2 pin has a series resistor on 6 of 7 designs, most often 20 kΩ (then 100 kΩ). Counted from the KiCad layouts of 7 open source designs using the OPA1656IDR.

What resistor goes on the OPA1656IDR -_6 pin?

The -_6 pin has a series resistor on 6 of 7 designs, most often 20 kΩ (then 10 Ω). Counted from the KiCad layouts of 7 open source designs using the OPA1656IDR.

What parts are used alongside the OPA1656IDR?

The OPA1612AIDR, OPA2192IDR and TPS7A2033PDBVR appear in the most repositories here.

Which microcontrollers do boards using the OPA1656IDR use?

Most are built on RP2040/RP2350 (1), Microchip SAM (1) and STM32 (1).

How big is a typical board using the OPA1656IDR?

The median is 165 × 105 mm, and 30% are two-layer designs.

What is the most popular open source board using the OPA1656IDR?

By GitHub stars, Pandore by filliformes, with 2 stars.

Can I simulate one of these boards using the OPA1656IDR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part