11 open source boards using the OPA1678
Real designs built with the OPA1678, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
OwmBoard
kanengomibako
55.4 × 66 mm158 parts2LUnlicense11OpenIEMA
aaravjhamb
40 × 69.8 mm53 parts2LNo license6AVR/Arduino
Esr meter
vpatkov
66 × 99.1 mm101 parts2LNo license5STM32
EuroSID
activexray
100 × 100 mm222 parts2LNo license3ESP32
Core
Hive-RSI-Lab
120 × 100 mm297 parts4LMIT0Analog via
starlingcode
213.5 × 128.5 mm269 parts4LCC-BY-NC-4.00ESP32
MOST25-to-AUDIO
Oleg-mk
98 × 60 mm174 parts4LCERN-OHL-S-2.00BTM308-host
KingJacker
23 × 40 mm52 parts4LNo license0ToneCTRL
dmsd-lab
45 × 45 mm72 parts2LCERN-OHL-S-2.00BTM308-host bottom
KingJacker
23 × 40 mm36 parts4LNo license0BufferVariator RevB
kanengomibako
100 × 100 mm100 parts2LUnlicense11
How designs wire the OPA1678
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the OPA1678 connects to, and the resistors, capacitors and other passives placed on it.
- The - pins have a series resistor on 9 of 9 designs, most often 10 kΩ (then 30 kΩ).
- Pin 1 has a series resistor on 8 of 9 designs, most often 10 kΩ (then 30 kΩ).
- Pin 7 has a series resistor on 8 of 9 designs, most often 1 kΩ (then 30 kΩ).
- The V+ pin has a decoupling capacitor on 8 of 9 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 89% |
|
| -pin 2, 6 | Connected to: Signal 100% |
|
| +pin 3, 5 | Connected to: Signal 83% |
|
| V-pin 4 | Connected to: GND 33% · -12V 33% · a signal 33% |
|
| Pin 7 | Connected to: Signal 100% |
|
| V+pin 8 | Connected to: 5V 89% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BufferVariator RevB by kanengomibako, OpenIEMA by aaravjhamb, Esr meter by vpatkov and EuroSID by activexray.
The OPA1678 in open source designs
The gallery holds 11 open source boards using the OPA1678 from 9 GitHub repositories; a typical one measures about 66 × 69.8 mm and carries around 101 components.
55% are two-layer designs, the rest use four layers or more, and 45% carry an open source license.
The most starred is OwmBoard by kanengomibako.
Parts used alongside the OPA1678
Microcontrollers on boards using the OPA1678
What boards using the OPA1678 are built for
OPA1678: common questions
Where can I find a OPA1678 reference design?
Each of the 11 boards on this page is a real design using the OPA1678. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the OPA1678 - pin?
The - pins have a series resistor on 9 of 9 designs, most often 10 kΩ (then 30 kΩ). Counted from the KiCad layouts of 9 open source designs using the OPA1678.
What resistor goes on the OPA1678 pin 1?
Pin 1 has a series resistor on 8 of 9 designs, most often 10 kΩ (then 30 kΩ). Counted from the KiCad layouts of 9 open source designs using the OPA1678.
What resistor goes on the OPA1678 pin 7?
Pin 7 has a series resistor on 8 of 9 designs, most often 1 kΩ (then 30 kΩ). Counted from the KiCad layouts of 9 open source designs using the OPA1678.
Which microcontrollers do boards using the OPA1678 use?
Most are built on ESP32 (2), STM32 (2) and AVR/Arduino (1).
How big is a typical board using the OPA1678?
The median is 66 × 69.8 mm, and 55% are two-layer designs.
What is the most popular open source board using the OPA1678?
By GitHub stars, OwmBoard by kanengomibako, with 11 stars.
Can I simulate one of these boards using the OPA1678 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.