5 open source boards using the PCF8575
Real designs built with the PCF8575, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Basicengine
uli
85 × 56 mm44 parts2LNo license48AVR/Arduino
BoardGame
jkordek1
150 × 150 mm176 parts2LNo license5BoneIO - external board
boneIO-eu
197 × 102 mm394 parts2LGPL-3.02ESP32
FarmGameV2
jkordek1
172.1 × 172.1 mm53 parts2LNo license0ESP32
MACK10 Controller
joehanko
57.3 × 67.1 mm43 parts2LNo license0
How designs wire the PCF8575
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the PCF8575 connects to, and the resistors, capacitors and other passives placed on it.
- The GND pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ.
- The P10 pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ.
- The P11 pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ.
- The SCL pin has a pull-up to VCC on 2 of 5 designs, most often 10 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 12 | Connected to: GND 60% · a signal 40% |
|
| P10pin 13 | Connected to: A connector 60% |
|
| P11pin 14 | Connected to: A connector 60% |
|
| SCLpin 22 | Connected to: The microcontroller 40% · not connected 40% |
|
| VCCpin 24 | Connected to: VCC 60% · not connected 20% · a signal 20% |
|
19 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Basicengine by uli, BoardGame by jkordek1, BoneIO - external board by boneIO-eu and FarmGameV2 by jkordek1.
The PCF8575 in open source designs
The gallery holds 5 open source boards using the PCF8575 from 5 GitHub repositories; a typical one measures about 150 × 102 mm and carries around 53 components.
100% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is Basicengine by uli.
Microcontrollers on boards using the PCF8575
What boards using the PCF8575 are built for
PCF8575: common questions
Where can I find a PCF8575 reference design?
Each of the 5 boards on this page is a real design using the PCF8575. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the PCF8575 GND pin?
The GND pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the PCF8575.
What pull-up resistor is used on the PCF8575 P10 pin?
The P10 pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the PCF8575.
What pull-up resistor is used on the PCF8575 P11 pin?
The P11 pin has a pull-up to 3.3V on 2 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 5 open source designs using the PCF8575.
Which microcontrollers do boards using the PCF8575 use?
Most are built on ESP32 (2), AVR/Arduino (1) and ESP8266 (1).
How big is a typical board using the PCF8575?
The median is 150 × 102 mm, and 100% are two-layer designs.
What is the most popular open source board using the PCF8575?
By GitHub stars, Basicengine by uli, with 48 stars.
Can I simulate one of these boards using the PCF8575 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.