8 open source boards using the QMC6309
Real designs built with the QMC6309, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Nordic nRF
Locus
Nieko27
40 × 40 mm50 parts4LCERN-OHL-S-2.060ESP32
Parsnip
LimesKey
60 × 130 mm400 parts4LCC-BY-NC-4.04Nordic nRF
Smd smores
infopcgood
18 × 21.1 mm50 parts2LNo license0SMORES
infopcgood
21 × 18 mm28 parts2LNo license0- schematic only · 33 partsESP32
SlimeVR-Tracker-ESP-Hardware
HelaFaye
33 partsApache-2.00 ESP32
Primis FaceTracker
Nieko27
95 × 48 mm44 parts2LCERN-OHL-S-2.060Nordic nRF
PicoRF Blk2B
madkoding
15 × 30 mm60 parts4LNo license0ESP32
Selftest amp2
LimesKey
30 × 20 mm9 parts2LCC-BY-NC-4.04
How designs wire the QMC6309
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the QMC6309 connects to, and the resistors, capacitors and other passives placed on it.
- The SCL pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 4.7 kΩ).
- The VDD pin has a decoupling capacitor on 4 of 5 designs, most often 2.2 µF (then 1 µF).
- The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 4.7 kΩ).
- The VDD pin has a crystal on 2 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSS_A1pin A1 | Connected to: GND 80% · 3.3V 20% | — |
| SCLpin A2 | Connected to: The microcontroller 40% |
|
| VDDpin B1 | Connected to: 3.3V 80% · GND 20% |
|
| SDApin B2 | Connected to: The microcontroller 40% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Locus by Nieko27, Parsnip by LimesKey, Smd smores pcb by infopcgood and SMORES by infopcgood.
The QMC6309 in open source designs
The gallery holds 8 open source boards using the QMC6309 from 6 GitHub repositories; a typical one measures about 30 × 30 mm and carries around 47 components.
57% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Locus by Nieko27.
Parts used alongside the QMC6309
Microcontrollers on boards using the QMC6309
What boards using the QMC6309 are built for
QMC6309: common questions
Where can I find a QMC6309 reference design?
Each of the 8 boards on this page is a real design using the QMC6309. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the QMC6309 SCL pin?
The SCL pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the QMC6309.
What decoupling capacitors do designs use on the QMC6309 VDD pin?
The VDD pin has a decoupling capacitor on 4 of 5 designs, most often 2.2 µF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the QMC6309.
What pull-up resistor is used on the QMC6309 SDA pin?
The SDA pin has a pull-up to 3.3V on 4 of 5 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 5 open source designs using the QMC6309.
Which microcontrollers do boards using the QMC6309 use?
Most are built on ESP32 (4) and Nordic nRF (3).
How big is a typical board using the QMC6309?
The median is 30 × 30 mm, and 57% are two-layer designs.
What is the most popular open source board using the QMC6309?
By GitHub stars, Locus by Nieko27, with 60 stars.
Can I simulate one of these boards using the QMC6309 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.