6 open source boards using the RFM98W-433S2

Real designs built with the RFM98W-433S2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the RFM98W-433S2

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the RFM98W-433S2 connects to, and the resistors, capacitors and other passives placed on it.

  • The DIO5 pins is left unconnected on 100% of them.
  • The DIO3 pins is left unconnected on 100% of them.
  • The DIO4 pins is left unconnected on 100% of them.
  • The DIO2 pins is left unconnected on 100% of them.
GNDpin 1, 1_1, 8, 8_1, 10, 10_1Connected to: GND 86%
NSSpin 5, 5_1Connected to: The microcontroller 86%, a connector 29%
  • Pull-up to 3.3V on 40% · 10 kΩ (3)
RESETpin 6, 6_1Connected to: The microcontroller 86%
  • Capacitor to GND on 40% · 100 nF (3), 1 µF (1)
DIO5pin 7, 7_1Connected to: Not connected 100%
ANTpin 9, 9_1Connected to: A connector 57%
  • Capacitor to GND on 40%
DIO3pin 11, 11_1Connected to: Not connected 100%
DIO4pin 12, 12_1Connected to: Not connected 100%
3.3Vpin 13, 13_1Connected to: 3.3V 86%
DIO0pin 14, 14_1Connected to: Signal 71% · not connected 29%
  • Series resistor on 40% · 100 Ω (3)
DIO1pin 15, 15_1Connected to: Not connected 86%
DIO2pin 16, 16_1Connected to: Not connected 100%

3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Kraky by thesh4dows, Fjalar flight controller by aesirkth, PCB by ApolLO-CanSat and PCB-temp by ApolLO-CanSat.

The RFM98W-433S2 in open source designs

The gallery holds 6 open source boards using the RFM98W-433S2 from 5 GitHub repositories; a typical one measures about 82 × 87.7 mm and carries around 60 components.

67% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.

The most starred is Kraky by thesh4dows.

Microcontrollers on boards using the RFM98W-433S2

RFM98W-433S2: common questions

Where can I find a RFM98W-433S2 reference design?

Each of the 6 boards on this page is a real design using the RFM98W-433S2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the RFM98W-433S2 DIO5 pin connected?

The DIO5 pins is left unconnected on 100% of them. Counted from the KiCad layouts of 5 open source designs using the RFM98W-433S2.

How is the RFM98W-433S2 DIO3 pin connected?

The DIO3 pins is left unconnected on 100% of them. Counted from the KiCad layouts of 5 open source designs using the RFM98W-433S2.

How is the RFM98W-433S2 DIO4 pin connected?

The DIO4 pins is left unconnected on 100% of them. Counted from the KiCad layouts of 5 open source designs using the RFM98W-433S2.

Which microcontrollers do boards using the RFM98W-433S2 use?

Most are built on ESP32 (3), RP2040/RP2350 (2) and STM32 (1).

How big is a typical board using the RFM98W-433S2?

The median is 82 × 87.7 mm, and 67% are two-layer designs.

What is the most popular open source board using the RFM98W-433S2?

By GitHub stars, Kraky by thesh4dows, with 1 stars.

Can I simulate one of these boards using the RFM98W-433S2 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part